Home › RESTRAINTS › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY

REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B133645
  1. Align the claws with the seat belt positioning holes, and install the retractor of the seat belt with the 2 bolts as shown in the illustration.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf } for upper bolt
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for lower bolt



    B133644
  1. Connect the shoulder anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body)


    B129714
  1. Attach the 7 clips to install the garnish.



3. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body)


    B129714
  1. Attach the 7 clips to install the garnish.



4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)


B129712
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 5 clips and 5 claws to install the trim board.

  1. Install the bolt and 2 screws.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)


    B129706
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 4 clips and 5 claws to install the trim board.

  1. Install the 2 screws and 2 bolts.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



6. CONNECT REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B133643
  1. Connect the seat belt's floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the lap belt outer anchor cover.



7. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)


8. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)


9. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


10. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH


11. INSTALL REAR FLOOR FINISH PLATE (for Short Body)


    B129716
  1. Attach the 6 clips to install the finish plate.



12. INSTALL REAR FLOOR FINISH PLATE (for Long Body)


    B129704
  1. Attach the 2 claws and 6 clips to install the finish plate.



13. INSTALL BACK DOOR WEATHERSTRIP


14. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Short Body)


B129717
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.



15. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Long Body)


B129705
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.



16. INSTALL JACK CARRIER ASSEMBLY (for Short Body)


    B129715
  1. Install the jack carrier with the 7 clips.



17. INSTALL REAR FLOOR NO. 3 BOARD


18. INSTALL REAR FLOOR NO. 2 BOARD


19. INSTALL DECK BOARD ASSEMBLY


20. INSTALL REAR FLOOR NO. 1 BOARD


21. INSTALL TONNEAU COVER ASSEMBLY


22. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY


23. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


24. INSTALL REAR DOOR SCUFF PLATE LH (for Short Body)


    B129711
  1. Attach the 8 claws to install the scuff plate.



25. INSTALL REAR DOOR SCUFF PLATE LH (for Long Body)


    B129703
  1. Attach the 9 claws and 2 clips to install the scuff plate.



26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL