Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

E115964E04

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E41-2 (SOL+) - E41-14 (GND)
    GR - W-B
    Compressor assembly with pulley operation signal
    1. Engine idling
    2. Refrigerant pressure: normal
    3. Blower switch lo
    4. A/C switch on
    Pulse generation
    (see waveform 1)
    E41-9 (PRE) - E41-13 (SG-2)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    Below 0.73 V
    E41-9 (PRE) - E41-13 (SG-2)
    L - G
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.14 MPa [32 kgf/cm2, 455 psi])
    4.84 V or higher
    E41-23 (BLW) - E41-14 (GND)
    R - W-B
    Blower motor control signal
    1. Ignition switch on (IG)
    2. Blower switch lo
    Pulse generation
    (see waveform 2)
    E41-33 (TSD) - E41-31 (S5-4)
    L - LG
    Driver side solar sensor signal
    1. Ignition switch on (IG)
    2. Solar sensor subject to electric light
    0.8 to 4.3 V
    E41-32 (TSP) - E41-31 (S5-4)
    P - LG
    Passenger side solar sensor signal
    1. Ignition switch on (IG)
    2. Solar sensor subject to electric light
    0.8 to 4.3 V
    E41-29 (TR) - E41-34 (SG-1)
    GR - V
    Room temperature sensor signal
    1. Ignition switch on (IG)
    2. Vehicle interior temperature: 25°C (77°F)
    1.8 to 2.2 V
    E41-34 (SG-1) - Body ground
    V - Body ground
    Ground for room temperature sensor
    Always
    Below 1 Ω
    E41-14 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 Ω
    E41-1 (IG+) - E41-14 (GND)
    Y - W-B
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    E41-21 (B) - E41-14 (GND)
    R - W-B
    Battery power source
    Always
    11 to 14 V
    E41-10 (S5-3) - E41-14 (GND)
    B - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    E41-11 (CANH) - E41-14 (GND)
    V - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 3)
    E41-12 (CANL) - E41-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 4)
    E41-13 (SG-2) - Body ground
    G - Body ground
    Ground for pressure sensor
    Always
    Below 1 Ω
    E41-3 (PTC1)*1,*2 - Body ground
    W - Body ground
    PTC NO. 1 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 75°C (167°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E41-22 (PTC2)*1,*2 - Body ground
    B - Body ground
    PTC NO. 2 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 70°C (158°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E41-4 (PTC3)*1,*3 - Body ground
    R - Body ground
    PTC NO. 3 relay operation signal
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 65°C (149°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off → lo
    Below 1 V → 11 to 14 V
    E41-25 (ALT) - Body ground
    B - Body ground
    Generator signal
    Engine idling
    Pulse generation
    E41-27 (HLS) - Body ground
    BR - Body ground
    Headlight signal
    1. Engine idling
    2. Headlight dimmer switch: on
    Below 1 V
    E41-37 (LIN1) - E41-14 (GND)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    c1-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 Ω
    c1-3 (BUS) - c1-2 (BUS G)
    -
    BUS IC control signal
    Ignition switch on (IG)
    Pulse generation
    c1-4 (B BUS) - c1-2 (BUS G)
    -
    Power supply for BUS IC
    Ignition switch on (IG)
    11 to 14 V
    c1-5 (SGA) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 Ω
    c1-6 (TEA) - c1-5 (SGA)
    -
    Evaporator temperature sensor signal
    1. Ignition switch on (IG)
    2. Evaporator temperature: 15°C (59°F)
    1.4 to 1.8 V

    1. *1: w/ PTC Heater
    2. *2: w/ Combustion Type Power Heater
    3. *3: w/o Combustion Type Power Heater



  2. E074977E18
  3. Using an oscilloscope, measure the waveform 1.
    Compressor and Pulley Operation Signal 
    Item
    Content
    Terminal No. (Symbol)
    E41-2 (SOL+) - E41-14 (GND)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    1. Refrigerant pressure: normal
    2. Engine idling
    3. Blower switch lo
    4. A/C switch on



  4. E103396E20
  5. Using an oscilloscope, measure the waveform 2.
    Blower Motor Control Signal 
    Item
    Content
    Terminal No. (Symbol)
    E41-23 (BLW) - E41-14 (GND)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    1. Ignition switch on (IG)
    2. Blower switch lo

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  6. A086154E46
  7. Using an oscilloscope, measure the waveform 3.
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    E41-11 (CANH) - E41-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.



  8. A086155E43
  9. Using an oscilloscope, measure the waveform 4.
    CAN Communication Signal 
    Item
    Content
    Terminal No. (Symbol)
    E41-12 (CANL) - E41-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.


CHECK AIR CONDITIONING CONTROL ASSEMBLY

E133021E03

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E109-2 (IG+) - E109-8 (GND)
    L - W-B
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    E109-8 (GND) - Body ground
    W-B - Body Ground
    Ground for air conditioning control assembly
    Always
    Below 1 V
    E109-12 (LIN1) - E109-8 (GND)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    E109-1 (+B) - E109-8 (GND)
    R - W-B
    Power source (Back-up)
    Always
    11 to 14 V
    E109-9 (ACC) - E109-8 (GND)
    GR - W-B
    ACC power supply
    Ignition switch on (ACC)
    11 to 14 V