Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.

WIRING DIAGRAM


E183908E01


E183909E01


INSPECTION PROCEDURE

1.INSPECT PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3*)
A092673E24
*: w/o Combustion Type Power Heater
  1. Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3* relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY (PTC NO. 1, PTC NO. 2, PTC NO. 3*)
OK


2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
E115805E17
  1. Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 75°C (167°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off
    Below 1 V*1
    E41-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 70°C (158°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off
    E41-4 (PTC3)*2 - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 65°C (149°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: off
    E41-3 (PTC1) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 75°C (167°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: lo
    11 to 14 V*1
    E41-22 (PTC2) - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 70°C (158°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: lo
    E41-4 (PTC3)*2 - Body ground
    1. Engine running (1250 rpm or more)
    2. Temperature setting: Max. hot
    3. Outside temperature: 10°C (50°F) or less
    4. Engine coolant temperature: 65°C (149°F) or less
    5. Headlight dimmer switch: off
    6. Blower switch: lo

    *1: After the measurement conditions are met, wait 30 seconds before performing measurements.
    *2: w/o Combustion Type Power Heater



NG
Go to step 6
OK


3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER)
E183405E01
  1. Remove the PTC heater relays from the engine room No. 2 relay block.

  1. Disconnect the A29 quick heater assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    w/o Combustion Type Power Heater: 
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 3 - A29-1 (B)
    Always
    Below 1 Ω
    PTC NO. 2 relay terminal 3 - A29-2 (B)
    PTC NO. 3 relay terminal 3 - A29-3 (B)
    PTC NO. 1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 2 relay terminal 3 - Body ground
    PTC NO. 3 relay terminal 3 - Body ground
    w/ Combustion Type Power Heater: 
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1 relay terminal 3 - A29-1 (B)
    Always
    Below 1 Ω
    PTC NO. 2 relay terminal 3 - A29-3 (B)
    PTC NO. 1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    PTC NO. 2 relay terminal 3 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT QUICK HEATER ASSEMBLY
E183954E01
E183953E01
  1. w/ Combustion Type Power Heater:

    1. Remove the quick heater assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (B) - 1 (E)
      Always
      Below 1 kΩ
      2 (B) - 1 (E)
      2 (B) - 2 (E)
      3 (B) - 2 (E)

  1. w/o Combustion Type Power Heater:

    1. Remove the quick heater assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A-1 (B) - B-1 (E)
      Always
      Below 1 kΩ
      A-2 (B) - B-1 (E)
      A-2 (B) - C-1 (E)
      A-3 (B) - C-1 (E)



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND)
E183409E01
E142217E09
  1. w/ Combustion Type Power Heater:

    1. Disconnect the A30 quick heater assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A30-1 (E) - Body ground
      Always
      Below 1 Ω
      A30-2 (E) - Body ground

  1. w/o Combustion Type Power Heater:

    1. Disconnect the A68 and A69 quick heater assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      A68-1 (E) - Body ground
      Always
      Below 1 Ω
      A69-1 (E) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BODY GROUND)
E183410E01
  1. Disconnect the E41 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E41-3 (PTC1) - Body ground
    Always
    Below 200 Ω
    E41-22 (PTC2) - Body ground
    E41-4 (PTC3)* - Body ground

    *: w/o Combustion Type Power Heater



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)