Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual room temperature displayed
    Open in the circuit: -6.5°C (20.3°F)
    Short in the circuit: 57.25°C (135.05°F)
    Ambient Temp Sensor
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature displayed
    Open in the circuit: -23.3°C (-9.94°F)
    Short in the circuit: 65.95°C (150.71°F)
    Adjusted Ambient Temp
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    -
    -
    Evaporator Fin Thermistor
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature displayed
    Open in the circuit: -29.7°C (-21.46°F)
    Short in the circuit: 59.55°C (139.19°F)
    Solar Sensor (D side)
    Driver side solar sensor /
    Min.: 0, Max.: 255
    Driver side solar sensor value increases as brightness increases
    -
    Solar Sensor (P side)
    Passenger side solar sensor /
    Min.: 0, Max.: 255
    Passenger side solar sensor value increases as brightness increases
    -
    Engine Coolant Temp
    Engine coolant temperature /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed after engine warmed up
    -
    Set Temperature (D side)
    Driver side set temperature /
    Min.: 0°C (32°F)
    Max.: 30°C (54°F)
    Driver side actual set temperature is displayed
    -
    Set Temperature (P side)
    Passenger side set temperature /
    Min.: 0°C (32°F)
    Max.: 30°C (54°F)
    Passenger side actual set temperature is displayed
    -
    Blower Motor Speed Level
    Blower motor speed level /
    Min.: 0 level, Max.: 31 level
    Increases 0 to 31 as blower motor speed increases
    -
    Regulator Pressure Sensor
    Regulator pressure sensor /
    Min.: -0.45668 MPaG
    Max.: 3.29437 MPaG
    Actual regulator pressure displayed
    -
    Regulator Control Current
    Compressor assembly with pulley /
    Min.: 0 A
    Max.: 0.997 A
    Value changes between 0 A and 0.997 A in accordance with compressor operation
    -
    Air Mix Servo Targ Pulse (D)
    Driver side air mix servo motor /
    Min.: 0, Max.: 255
    LHD:
    Max. cold: 92 (pulse)
    Max. hot: 5 (pulse)
    RHD:
    Max. cold: 6 (pulse)
    Max. hot: 93 (pulse)
    -
    Air Mix Servo Targ Pulse (P)
    Passenger side air mix servo motor /
    Min.: 0, Max.: 255
    LHD:
    Max. cold: 6 (pulse)
    Max. hot: 93 (pulse)
    RHD:
    Max. cold: 92 (pulse)
    Max. hot: 5 (pulse)
    -
    Air Outlet Servo Pulse (D)
    Air outlet damper servo motor /
    Min.: 0, Max.: 255
    FACE: 47 (pulse)
    B/L: 37 (pulse)
    FOOT: 17 (pulse)
    FOOT/DEF: 9 (pulse)
    DEF: 5 (pulse)
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper servo motor /
    Min.: 0, Max.: 255
    LHD:
    RECIRCULATION: 19 (pulse)
    FRESH: 7 (pulse)
    RHD:
    RECIRCULATION: 7 (pulse)
    FRESH: 25 (pulse)
    -
    Electric Heater Count*
    Electric (PTC) heater count /
    Min.: 0
    Max.: 3
    Actual number of the heater elements to be heated is displayed
    -
    Shift Set Temperature
    Shift set temperature / 2 C incr, 1 C incr, NORMAL, 1 C decr, 2 C decr
    Customized value displayed
    -
    Air Inlet Mode
    Air inlet mode /
    AUTO, MANUAL
    Customized value displayed
    -
    Compressor Mode
    Compressor mode /
    AUTO, MANUAL
    Customized value displayed
    -
    Compressor/DEF Mode
    Compressor / DEF Mode /
    LINK, NORMAL
    Customized value displayed
    -
    Evaporator Control
    Evaporator Control /
    AUTO, MANUAL
    Customized value displayed
    -
    Foot/DEF Auto Mode
    Foot / DEF auto mode /
    ON, OFF
    Customized value displayed
    -
    Foot/DEF Auto Blow Up
    Foot / DEF automatic blow up function /
    ON, OFF
    Customized value displayed
    -
    Ambient Temperature Shift
    Ambient temperature shift / 3C incr, 2C incr, 1C incr, Normal, 1C decr, 2C decr, 3C decr
    Customized value displayed
    -
    Number of Trouble Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs displayed
    -

    1. *: w/ PTC Heater


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Air Conditioner / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    Defogger Relay (Rear)
    Defogger relay (Rear)
    ON or OFF
    -
    Electric Heater 1*1,*2
    No. 1 PTC heater relay
    ON or OFF
    -
    Electric Heater 2*1,*2
    No. 2 PTC heater relay
    ON or OFF
    -
    Electric Heater 3*1,*3
    No. 3 PTC heater relay
    ON or OFF
    -
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor pulse (D side)
    Min.: 0, Max.: 255
    -
    Air Mix Servo Targ Pulse (P)
    Air mix servo motor pulse (P side)
    Min.: 0, Max.: 255
    -
    Air Outlet Servo Pulse (D)
    Air outlet servo motor pulse
    Min.: 0, Max.: 255
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 0, Max.: 255
    -

    1. *1: w/ PTC Heater
    2. *2: w/ Combustion Type Power Heater
    3. *3: w/o Combustion Type Power Heater