Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING PANEL (for Manual Air Conditioning System)

AIR CONDITIONING PANEL (for Manual Air Conditioning System) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208365
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



3. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208366
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



4. REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)


  1. w/o Stereo Opening Cover:

    1. Remove the 4 bolts.



    2. Pull the radio receiver to detach the 2 claws and 4 clips on the backside of the radio receiver.


      B219615

    3. Disconnect all connectors and remove the radio receiver with bracket.



  1. w/ Stereo Opening Cover:

    1. Remove the 4 bolts.



    2. Pull the radio receiver to detach the 2 claws and 4 clips on the backside of the radio receiver.


      B219616

    3. Disconnect all connectors and remove the radio receiver with bracket.



5. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B133002
  1. Remove the 4 bolts.

  1. Detach the 4 clips and remove the stereo opening cover.



6. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for DVD)


  1. for 2AD-FTV, 2AD-FHV:

    1. Remove the 4 bolts.



    2. Pull the navigation receiver to detach the 2 claws and 4 clips on the backside of the navigation receiver.


      B220641

    3. Disconnect all the connectors and remove the navigation receiver.



  1. except 2AD-FTV, 2AD-FHV:

    1. Remove the 4 bolts.



    2. Pull the navigation receiver to detach 2 claws and 4 clips on the backside of the navigation receiver.


      B219744

    3. Disconnect all the connectors and remove the navigation receiver.



7. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for HDD)
  1. Remove the 4 bolts.



  1. Pull the navigation receiver to detach the 2 claws and 4 clips on the backside of the navigation receiver.


    B219744

  1. Disconnect all connectors and remove the radio navigation with bracket.



8. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E118688
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the 3 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the connectors and remove the air conditioning control.



9. REMOVE AIR MIX CONTROL SWITCH


    E118685
  1. Detach the 2 claws and remove the air mix control switch.



10. REMOVE BLOWER CONTROL SWITCH


    E118686
  1. Detach the 2 claws and remove the blower control switch.



11. REMOVE AIR VENT MODE CONTROL SWITCH


    E118687
  1. Detach the 2 claws and remove the mode control switch.