Home › BODY › ENGINE HOOD / DOOR › BACK DOOR

BACK DOOR > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL STOPPER


2. INSTALL CUSHION
  1. Remove the 2 cushions.



3. INSTALL BACK DOOR SIDE FEMALE STOPPER
  1. Install the stopper with the 2 bolts.



4. INSTALL BACK DOOR CHECK ASSEMBLY


    B129933
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf } for nut

  1. Apply adhesive to the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the door check to the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf } for bolt



5. INSTALL DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)


    B132806
  1. Install the door electrical key oscillator with the screw.



6. INSTALL BACK DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Install the front door lock open rod.



    B133688
  1. Attach the claw and clip to install the frame.



    B129935
  1. Using a T30 "TORX" socket, install the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B129936
  1. w/ Entry and Start System
    Connect the clamp and connector.



7. INSTALL DOOR OUTSIDE HANDLE PAD


    B133567
  1. Attach the 2 claws to install the pad.



8. INSTALL BACK DOOR REAR OUTSIDE HANDLE PAD


    B133568
  1. Attach the 2 claws to install the pad.



9. INSTALL BACK DOOR OUTSIDE HANDLE
  1. w/ Entry and Start System
    Connect the connector.



    B133664
  1. Install the handle by pushing and sliding it in the direction indicated by the arrows in the illustration.



10. INSTALL BACK DOOR OUTSIDE HANDLE COVER


    B129937E01
  1. Using a T30 "TORX" socket, install the cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



11. INSTALL BACK DOOR LOCK ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the back door lock.



    B133655E01
  1. Install a new door lock wire harness packing.

    NOTICE:
    1. When reinstalling the door lock, always use new packing.
    2. Do not allow grease or dirt to contaminate the gap between the door panel and packing.
    3. Old or damaged packing cannot effectively protect against water which can damage the door lock.



    B129946E01
  1. Connect the control rod into the door lock, and then set it to the door panel.

    NOTICE:
    Make sure that the rod is securely engaged with the lock.

  1. Apply adhesive to the threads of the 3 screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B129939
  1. Using a T30 "TORX" socket, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



12. INSTALL BACK DOOR SERVICE HOLE COVER


    B139375
  1. Apply butyl tape to the door panel, then install a new back door service hole cover as shown in the illustration.

    HINT:
    1. When installing the service hole cover, pull out the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. Connect each connector.



13. INSTALL REAR WIPER MOTOR ASSEMBLY


B131460
  1. Install the wiper motor with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



14. INSTALL UPPER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY RH (w/ Tire Carrier)


B208687
  1. Install 6 new clips to the back door outside garnish.

  1. Attach the 6 clips to install the back door outside garnish.



15. INSTALL LOWER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY RH (w/ Tire Carrier)


B208681
  1. Install 5 new clips to the back door outside garnish.

  1. Attach the claw and 5 clips to install the back door outside garnish.



16. INSTALL UPPER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY LH (w/ Tire Carrier)


B208684
  1. Install 6 new clips to the back door outside garnish.

  1. Attach the 6 clips to install the back door outside garnish.

  1. Install the screw.



17. INSTALL REAR FOG LIGHT ASSEMBLY (w/ Rear Fog Light)


B132932
  1. Connect the connector.

  1. Install the rear fog light with the 2 screws.



18. INSTALL LICENSE PLATE LIGHT ASSEMBLY (w/ License Plate Light)


B135719
  1. Install the light as shown in the illustration.

  1. Connect the connector.



19. INSTALL BACK DOOR GARNISH COVER (for 1-piece Type)


B208325
  1. Attach the 2 claws to install the back door garnish cover.



20. INSTALL LOWER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY LH (w/ Tire Carrier)
  1. Install new clips to the back door outside garnish.

  1. w/ License Plate Light:
    Connect the license plate light connector.

  1. w/ Rear Fog Light:
    Connect the rear fog light connector.

  1. Install the back door outside garnish.

    1. Attach the clips to install the back door outside garnish.



  1. Install the screw.


    B209954E02



21. INSTALL BACK DOOR OUTSIDE GARNISH CLIP (w/o Tire Carrier)


B219391
  1. Install the 2 clips with the 2 screws.



22. INSTALL LOWER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/o Tire Carrier)


B219390
  1. Attach the 15 clips and claw to install the back door outside garnish.



23. INSTALL TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


    B132925
  1. Install the television camera with the screw.



    B132924
  1. Attach the clamp and connect the television camera connector.



24. INSTALL LICENSE PLATE LIGHT ASSEMBLY (w/o Tire Carrier)


B140226
  1. Install the light as shown in the illustration.

  1. Install the screw.

  1. Connect the connector.



25. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/o Tire Carrier)


B219389
  1. Install the grommet to the back door panel.

  1. Attach the 6 clips to install the back door outside garnish.



    B219388
  1. Install the 3 nuts.



    B182786
  1. Connect the connector.



26. INSTALL SPARE WHEEL CARRIER BRACKET SUB-ASSEMBLY (w/ Tire Carrier)


  1. w/o Breakaway Bolts:
    Install the spare wheel carrier bracket.



      B139540
    1. Detach the 2 clips to install the carrier bracket.



    2. B139538
    3. Install the 4 bolts.

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }



  1. w/ Breakaway Bolts:
    Install the spare wheel carrier bracket.



      B139540
    1. Detach the 2 clips to install the carrier bracket.



    2. B139539
    3. Install the 2 bolts.

      Torque:
      28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    4. B139759
    5. Tighten the 2 new breakaway bolts until the bolt heads break off.



27. INSTALL CENTER STOP LIGHT ASSEMBLY


B131434
  1. Install the center stop light with the 2 screws.

  1. Connect the connector.



28. INSTALL REAR SPOILER
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

  1. If reusing the spoiler:
    Clean the spoiler.

    1. Using a heat light, heat the spoiler.

  1. Connect the center stop light connector.



    B127944
  1. Install the spoiler with 3 clips.



    B127943
  1. Install the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



29. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
  1. Stop the wiper motor at the automatic stop position.



    B117856E02
  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    E125268E03
  1. Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    1. Hold down the arm hinge by hand while tightening the nut.
    2. Install the arm and blade so that the rear wiper blade is aligned with the defogger line.



    B136379
  1. Install the cap.



30. INSTALL BACK DOOR TRIM BOARD ASSEMBLY
  1. Install the back door trim pocket with the 5 screws.



    B129943
  1. Attach the 13 clips to install the trim board.



31. INSTALL BACK DOOR COURTESY LIGHT ASSEMBLY


B131446
  1. Connect the connector.

  1. Install the switch with the bolt.



32. INSTALL BACK DOOR SIDE GARNISH LH


    B129945
  1. Attach the 2 claws and 2 clips to install the garnish.



33. INSTALL BACK DOOR SIDE GARNISH RH

HINT:
Use the same procedure described for the LH side.



34. INSTALL BACK DOOR CENTER GARNISH


    B129944
  1. Attach the 4 claws and 4 clips to install the garnish.



35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL