Home › BRAKE › PARKING BRAKE › PARKING BRAKE ASSEMBLY

PARKING BRAKE ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. APPLY HIGH TEMPERATURE GREASE
  1. Apply high temperature grease to the contact surface of the shoe and backing plate.



2. INSTALL PARKING BRAKE SHOE LEVER LH


3. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH
  1. Connect the parking brake cable to the parking brake shoe lever.



    C129082E03
  1. Apply high temperature grease to the following contact surfaces of the shoe.

    1. Shoe to anchor pin
    2. Shoe to parking brake lever pin
    3. Shoe to spring



    C127306
  1. Install the shoe with the shoe hold-down spring and pin.



4. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH


    C129083E03
  1. Apply high temperature grease to the following contact surfaces of the shoe.

    1. Shoe to anchor pin
    2. Shoe to spring



    C127305
  1. Install the shoe with the shoe hold-down spring and pin.



5. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    C193371E01
  1. Apply high temperature grease to the areas of the shoe adjusting screw set shown in the illustration.

  1. Install the screw set.



6. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)
  1. Using needle-nose pliers, install the tension spring.



7. INSTALL PARKING BRAKE SHOE STRUT LH


    C129084E03
  1. Apply high temperature grease to the contact surface of the strut and shoe return tension spring.

  1. Install the strut.



8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING (for Upper Side)


    C127312
  1. Using needle-nose pliers, install the 2 shoe return tension springs.



9. CHECK PARKING BRAKE INSTALLATION


  1. Check that each part is installed properly.


    C127313E01

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and disc.



10. INSTALL REAR DISC


    C129072E01
  1. Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



11. ADJUST PARKING BRAKE SHOE CLEARANCE
  1. Temporarily install the hub nuts.



    C127310E01
  1. Remove the shoe adjusting hole plug, and then turn the adjuster to expand the shoe adjuster until the disc locks.

  1. Turn the shoe adjuster so that it contracts to a point where the disc can rotate smoothly.

    Standard:
    8 notches

  1. Check that the shoe has no brake drag.



12. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the shoe adjusting hole plug to the rear disc.



13. CONNECT REAR DISC BRAKE CYLINDER MOUNTING LH


    C127287
  1. Install the cylinder mounting with the 2 bolts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



14. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



15. SETTLE PARKING BRAKE SHOE AND DISC
  1. Pull the parking brake lever with a force of 147 N (15 kgf, 33 lbf).

  1. Drive the vehicle at approximately 50 km/h (31 mph) for approximately 400 m (0.25 miles).

    NOTICE:
    Drive the vehicle on a safe, level and dry road.

  1. Repeat the above steps 2 or 3 times.



16. CHECK PARKING BRAKE LEVER TRAVEL
  1. Pull the lever upward with a force of approximately 200 N (20 kgf, 44 lbf) and count the number of clicks.

    OK:
    6 to 8 clicks (without rear brake dragging)



17. ADJUST PARKING BRAKE LEVER TRAVEL


    C127319E01
  1. Turn the No. 1 wire adjusting nut until the lever travel is correct.

    OK:
    6 to 8 clicks (without rear brake dragging)
    <Lever pulling force: approximately 200 N (20 kgf, 44 lbf)>

  1. Tighten the lock nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

    OK:
    6 to 8 clicks (without rear brake dragging)
    <Lever pulling force: approximately 200 N (20 kgf, 44 lbf)>

  1. When operating the parking brake lever, check that the brake warning light illuminates at the first click.

    Standard condition:
    Brake warning light always illuminates at the first click.