Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

When the stop light switch is turned on, current flows to the stop lights to illuminate them.

WIRING DIAGRAM


E174419E01


E174420E01


E177789E01


E125182E03


INSPECTION PROCEDURE

1.CHECK VEHICLE EQUIPMENT
  1. Check if the stop light control relay is equipped on the vehicle.
    Result 
    Result
    Proceed to
    w/ stop light control relay
    A
    w/o stop light control relay
    B



B
Go to step 12
A


2.INSPECT FUSE (STOP)
  1. Remove the STOP fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


3.INSPECT STOP LIGHT SWITCH
E164228E02
  1. Remove the stop light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    10 kΩ higher
    Pin released
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    Pin released
    10 kΩ higher



NG
REPLACE STOP LIGHT SWITCH
OK


4.CHECK WIRE HARNESS (STOP LIGHT SWITCH - BATTERY)
E166339E02
  1. Disconnect the A66 stop light switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A66-2 - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK STOP LIGHT CONTROL RELAY
E174994E01
  1. Measure the voltage of the stop light control relay.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A70-8 (OUT) - Body ground
    Brake pedal released
    Below 1 V
    Brake pedal depressed
    11 to 14 V



NG
Go to step 10
OK


6.INSPECT STOP LIGHT (REAR COMBINATION LIGHT)
B118217E09
  1. Remove the rear combination light.

  1. Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 1, then check that the light comes on.

    OK:
    Light comes on.



NG
REPLACE REAR COMBINATION LIGHT
OK


7.INSPECT REAR STOP LIGHT (HIGH MOUNT STOP LIGHT)
E174551E01
  1. Remove the high mount stop light assembly.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the light comes on.

    OK:
    Light comes on

    Result 
    Result
    Proceed to
    OK (w/ VSC)
    A
    OK (w/o VSC)
    B
    NG
    C



B
Go to step 9

C
REPLACE HIGH MOUNT STOP LIGHT ASSEMBLY
A


8.INSPECT BRK RELAY
A087121E06
  1. Remove the BRK relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 4
    10 kΩ or higher
    (Battery voltage applied to terminals 1 and 2)
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (Battery voltage applied to terminals 1 and 2)



NG
REPLACE BRK RELAY
OK


9.CHECK WIRE HARNESS (STOP LIGHT CONTROL RELAY - REAR STOP LIGHT)
E173479E02
  1. Disconnect the A70 stop light control relay connector.

  1. Disconnect the K13 (for RH) and K15 (for LH) rear combination light connectors.

  1. Disconnect the S1 high mount stop light connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A70-8 (OUT) - K13-4
    Below 1 Ω
    A70-8 (OUT) or K13-4 - Body ground
    10 kΩ or higher
    A70-8 (OUT) - K15-4
    Below 1 Ω
    A70-8 (OUT) or K15-4 - Body ground
    10 kΩ or higher
    A70-8 (OUT) - S1-2
    Below 1 Ω
    A70-8 (OUT) or S1-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR STOP LIGHT - BODY GROUND) 

10.CHECK WIRE HARNESS (STOP LIGHT CONTROL RELAY - BATTERY AND BODY GROUND)
E142629E24
  1. Disconnect the A70 stop light control relay connector.

  1. Measure the resistance of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A70-6 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A70-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


11.CHECK WIRE HARNESS (STOP LIGHT SWITCH - STOP LIGHT CONTROL RELAY)
E173812E02
  1. Disconnect the A66 stop light switch connector.

  1. Disconnect the A70 stop light control relay connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A66-1 - A70-2 (STP)
    Below 1 Ω
    A66-1 or A70-2 (STP) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE STOP LIGHT CONTROL RELAY 

12.REPLACE FUSE (STOP)
  1. Remove the STOP fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


13.INSPECT STOP LIGHT (REAR COMBINATION LIGHT)
B118217E03
  1. Remove the rear combination light.

  1. Connect the positive (+) lead from the battery to terminal 4 and the negative (-) lead to terminal 1, then check that the light comes on.

    OK:
    Light comes on.



NG
REPLACE REAR COMBINATION LIGHT
OK


14.INSPECT STOP LIGHT (HIGH MOUNT STOP LIGHT)
B118219E01
  1. Remove the high mount stop light.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the light comes on.

    OK:
    Light comes on

    Result 
    Result
    Proceed to
    OK: w/ VSC
    A
    OK: w/o VSC
    B
    NG
    C



B
Go to step 16

C
REPLACE HIGH MOUNT STOP LIGHT ASSEMBLY
A


15.INSPECT BRK RELAY
A087121E06
  1. Remove the BRK relay from the engine room No. 1 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 4
    Below 1 Ω
    3 - 4
    10 kΩ or higher
    (Battery voltage applied to terminals 1 and 2)
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (Battery voltage applied to terminals 1 and 2)



NG
REPLACE BRK RELAY
OK


16.INSPECT STOP LIGHT SWITCH


    B113724E10
  1. Remove the stop light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    10 kΩ higher
    Pin released
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    Pin released
    10 kΩ higher



NG
REPLACE STOP LIGHT SWITCH
OK


17.CHECK WIRE HARNESS (STOP LIGHT SWITCH - BATTERY)


    B124046E07
  1. Disconnect the A5 stop light switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    A5-2 - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


18.CHECK WIRE HARNESS (STOP LIGHT SWITCH - REAR STOP LIGHT)
E125081E04
  1. Disconnect the A5 stop light switch connector.

  1. Disconnect the K13 and K15 rear combination light connectors.

  1. Disconnect the S1 high mount stop light connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A5-1 - K13-4
    Below 1 Ω
    A5-1 or K13-4 - Body ground
    10 kΩ or higher
    A5-1 - K15-4
    Below 1 Ω
    A5-1 or K15-4 - Body ground
    10 kΩ or higher
    A5-1 - S1-2
    Below 1 Ω
    A5-1 or S1-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR STOP LIGHT - BODY GROUND)