LIGHTING SYSTEM > Hazard Warning Switch Circuit |


| 1.CHECK VEHICLE CONDITION |
Check the vehicle condition.
| Result | Proceed to |
| LHD | A |
| RHD | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the Active Test and then check the relay operation.
| Item | Test Details/Display (Range) | Diagnostic Note |
| Hazard | Hazard ON/OFF | - |
|
| ||||
| NG | |
| 3.INSPECT FUSE (HAZ) |
Remove the HAZ fuse from the engine room No. 1 relay block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - BATTERY) |
![]() |
Remove the turn signal flasher relay from the instrument panel junction block.
Measure the voltage of the junction block.
| Tester Connection | Specified Condition |
| Junction block turn signal flasher relay terminal 4 (+B) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 5.CHECK OPERATION OF TURN SIGNAL FLASHER RELAY |
Replace the turn signal flasher relay with a normally functioning one or a new one.
Check that the appropriate turn signal light flashes.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the Active Test and then check the relay operation.
| Item | Test Details/Display (Range) | Diagnostic Note |
| Hazard | Hazard ON/OFF | - |
|
| ||||
| OK | ||
| ||
| 6.INSPECT HAZARD WARNING SIGNAL SWITCH |
![]() |
Remove the hazard warning signal switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 4 | OFF | 10 kΩ or higher |
| 1 - 4 | ON | Below 23.4 Ω |
|
| ||||
| OK | ||
| ||
| 7.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the Active Test and then check the relay operation.
| Item | Test Details/Display (Range) | Diagnostic Note |
| Hazard | Hazard ON/OFF | - |
|
| ||||
| NG | |
| 8.INSPECT FUSE (HAZ) |
Remove the HAZ fuse from the engine room No. 1 relay block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (TURN SIGNAL FLASHER RELAY - BATTERY) |
![]() |
Disconnect the E81 turn signal flasher relay connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E81-4 (B) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 10.CHECK OPERATION OF TURN SIGNAL FLASHER RELAY |
Replace the turn signal flasher relay with a normally functioning one or a new one.
Check that the appropriate turn signal light flashes.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the Active Test and then check the relay operation.
| Item | Test Details/Display (Range) | Diagnostic Note |
| Hazard | Hazard ON/OFF | - |
|
| ||||
| OK | ||
| ||
| 11.INSPECT HAZARD WARNING SIGNAL SWITCH |
![]() |
Remove the hazard warning signal switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
| 1 - 4 | OFF | 10 kΩ or higher |
| 1 - 4 | ON | Below 23.4 Ω |
|
| ||||
| OK | ||
| ||