LIGHTING SYSTEM > Taillight Relay Circuit |


| 1.CHECK WHETHER LIGHTS ILLUMINATE |
Check whether the following lights illuminate: front clearance lights, rear taillights, license plate light.
| Result | Proceed to |
| All lights do not illuminate | A |
| Front clearance lights do not illuminate | B |
| Rear taillights do not illuminate | C |
| License plate light does not illuminate | D |
| All lights illuminate | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT FUSE (TAIL) |
Remove the TAIL fuse from the instrument panel junction block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 3.CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY) |
![]() |
Disconnect the IG instrument panel junction block connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| IG-1 - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH) |

Disconnect the E18 main body ECU connector.
Disconnect the E15 headlight dimmer switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E18-21 (TAIL) - E15-18 (T) | Below 1 Ω |
| Tester Connection | Specified Condition |
| E18-21 (TAIL) - E15-13 (T) | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (HEADLIGHT DIMMER SWITCH - BATTERY) |
![]() |
Connect the E18 main body ECU connector.
Disconnect the E15 headlight dimmer switch connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| E15-18 (T) - Body ground | 10 to 14 V |
| Tester Connection | Specified Condition |
| E15-13 (T) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (HEADLIGHT DIMMER SWITCH - BODY GROUND) |
![]() |
Disconnect the E15 headlight dimmer switch connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
| E15-12 (EL) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| E15-19 (EL) - Body ground | Below 1 Ω |
|
| ||||
| OK | |
| 7.INSPECT HEADLIGHT DIMMER SWITCH |
![]() |
Remove the headlight dimmer switch.
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
| 18 (T) - 12 (EL) | OFF | 10 kΩ or higher |
| 18 (T) - 12 (EL) | TAIL | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| 13 (T) - 19 (EL) | OFF | 10 kΩ or higher |
| 13 (T) - 19 (EL) | TAIL | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 8.CHECK INSTRUMENT PANEL JUNCTION BLOCK (TAILLIGHT RELAY) |
![]() |
Disconnect the IB instrument panel junction block connectors.
Measure the voltage of the junction block.
| Tester Connection | Condition | Specified Condition |
| Junction block IB terminal 15 - Body ground | Light control switch TAIL | 10 to 14 V |
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (JUNCTION BLOCK - FRONT CLEARANCE LIGHT AND BODY GROUND) |
![]() |
Disconnect the A20 and A33 front clearance light connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| A20-2 - Body ground | Light control switch TAIL | 10 to 14 V |
| A33-2 - Body ground | Light control switch TAIL | 10 to 14 V |
| Tester Connection | Specified Condition |
| A20-1 - Body ground | Below 1 Ω |
| A33-1 - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 10.CHECK WIRE HARNESS (MAIN BODY ECU - REAR COMBINATION LIGHT) |
![]() |
Disconnect the K13 and K15 rear combination light connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| K15-2 - Body ground | Light control switch on (TAIL) | 10 to 14 V |
| K13-2 - Body ground | Light control switch on (TAIL) | 10 to 14 V |
| Tester Connection | Specified Condition |
| K15-1 - Body ground | Below 1 Ω |
| K13-1 - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 11.CHECK WIRE HARNESS (MAIN BODY ECU - LICENSE PLATE LIGHT AND BODY GROUND) |
![]() |
for Short body (w/o Tire Carrier):
Disconnect the S6 license plate light connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| S6-1 - Body ground | Light control switch TAIL | 10 to 14 V |
| Tester Connection | Specified Condition |
| S6-2 - Body ground | Below 1 Ω |
![]() |
for Short body (w/ Tire Carrier):
Disconnect the N3 license plate light connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| N3-2 - Body ground | Light control switch TAIL | 10 to 14 V |
| Tester Connection | Specified Condition |
| N3-1 - Body ground | Below 1 Ω |
![]() |
for Long body (w/o Rear fog light):
Disconnect the S6 license plate light connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| S6-2 - Body ground | Light control switch TAIL | 10 to 14 V |
| Tester Connection | Specified Condition |
| S6-1 - Body ground | Below 1 Ω |
![]() |
for Long body (w/ Rear fog light):
Disconnect the N2 license plate light connector.
Measure the voltage and resistance of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| N2-2 - Body ground | Light control switch TAIL | 10 to 14 V |
| Tester Connection | Specified Condition |
| N2-1 - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||