Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Back-up Light Circuit

for Preparation Click here


DESCRIPTION

A/T models: The park/neutral position switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.
M/T models: The back-up light switch turns on when the shift lever is moved into the R position, causing the back-up light to illuminate.

WIRING DIAGRAM


B128020E01


INSPECTION PROCEDURE

1.INSPECT FUSE (GAUGE1)
  1. Remove the GAUGE1 fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


2.INSPECT BULB (BACK-UP LIGHT BULB)
B118217E08
  1. Remove the rear combination light assembly.

  1. Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE BULB
OK


3.CHECK TRANSAXLE TYPE

Result:
Transaxle Type
Proceed to
A/T
A
M/T
B



B
Go to step 7
A


4.INSPECT PARK / NEUTRAL POSITION SWITCH
C110340E27
  1. Disconnect the B28 park / neutral position switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Condition
    Shift Position
    Specified Condition
    2 (RB) - 1 (RL)
    R
    Below 1 Ω
    2 (RB) - 1 (RL)
    Except R
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH
OK


5.CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY)
B124048E05
  1. Disconnect the B28 park / neutral position switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    B28-2 (RB) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK WIRE HARNESS (SWITCH - REAR COMBINATION LIGHT)
E125301E04
  1. Disconnect the B28 park/neutral position switch connector.

  1. Disconnect the K13 or K15 rear combination light connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Condition
    Specified Condition
    B28-1 - K13-1
    Below 1 Ω
    B28-1 - K15-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - BODY GROUND) 

7.INSPECT BACK-UP LIGHT SWITCH
B117875E02
  1. Disconnect the B25 back-up light switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Condition
    Shift Position
    Specified Condition
    2 - 1
    R (Pushed)
    Below 1 Ω
    2 - 1
    Except R (Not pushed)
    10 kΩ or higher



NG
REPLACE BACK-UP LIGHT SWITCH
OK


8.CHECK WIRE HARNESS (BACK-UP LIGHT SWITCH - BATTERY)
B128027E01
  1. Disconnect the B25 back-up light switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Condition
    Condition
    Specified Condition
    B25-2 - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9.CHECK WIRE HARNESS (BACK-UP LIGHT SWITCH - REAR COMBINATION LIGHT)
B128028E03
  1. Disconnect the B25 back-up light switch connector.

  1. Disconnect the K13 and K15 rear combination light connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Condition
    Specified Condition
    B25-1 - K13-1
    Below 1 Ω
    B25-1 - K15-1
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - BODY GROUND)