UPPER INSTRUMENT PANEL > INSTALLATION |
| 1. INSTALL UPPER INSTRUMENT PANEL |
Attach the 6 clips and 5 claws to install the instrument panel.
Connect the connector and attach the clamp.
Install the 2 bolts and 2 screws.
Connect the passenger airbag connector.

![]() |
Install the 2 bolts to the passenger airbag.
| 2. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Attach the 2 hinges to install the door.
![]() |
Attach the claw to the glove compartment door stopper.
While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
| 3. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 antenna cord clamps.
![]() |
w/ Curtain Shield Airbag:
Install 2 new clips to the front pillar garnish.
Attach the 3 claws and 2 clips to install the garnish.
w/o Curtain Shield Airbag:
![]() |
Attach the 2 clips and 2 claws to install the garnish.
| 4. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 wire harness clamps.
![]() |
w/ Curtain Shield Airbag:
Install 2 new clips to the front pillar garnish.
Attach the 3 claws and 2 clips to install the garnish.
w/o Curtain Shield Airbag:
![]() |
Attach the 2 clips and 2 claws to install the garnish.
| 5. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY CENTER |
![]() |
Attach the 5 clips to install the instrument panel register.
| 6. INSTALL STEREO OPENING COVER (w/o Radio Receiver) |
![]() |
Attach the 4 clips to install the stereo opening cover.
Install the 4 bolts.
| 7. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver) |
w/o Stereo Opening Cover:
Connect all the connectors and install the radio receiver.
Insert the radio receiver to attach the 2 claws and 4 clips on its backside.
Install the 4 bolts.

w/ Stereo Opening Cover:
Connect all the connectors and install the radio receiver.
Insert the radio receiver to attach the 2 claws and 4 clips on its backside.
Install the 4 bolts.

| 8. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System) |
for 2AD-FTV, 2AD-FHV:
Connect all the connectors to install the navigation receiver.
Insert the navigation receiver to attach the 2 claws and 4 clips on its backside.
Install the 4 bolts.

except 2AD-FTV, 2AD-FHV:
Connect all the connectors to install the navigation receiver.
Insert the navigation receiver to attach the 2 claws and 4 clips on its backside.
Install the 4 bolts.

| 9. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for HDD) |
Connect all connectors to install the navigation receiver.
Insert the navigation receiver to attach the 2 claws and 4 clips on its backside.
Install the 4 bolts.

| 10. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() |
Connect the connector.
Attach the 3 clips and 2 claws to install the cluster finish panel.
| 11. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER |
![]() |
Connect the connector.
Attach the 3 clips and 2 claws to install the cluster finish panel.
| 12. INSTALL COMBINATION METER ASSEMBLY |
![]() |
Connect the connector.
Attach the 2 clips to install the combination meter.
Install the 2 screws.
| 13. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
![]() |
Attach the 4 clips and 6 claws to install the instrument cluster finish panel.
| 14. INSTALL STEERING WHEEL ASSEMBLY (for LHD) |
![]() |
Align the matchmarks and install the steering wheel to the steering column.
Install the nut.
Connect all the connectors to the spiral cable.
| 15. INSTALL STEERING WHEEL ASSEMBLY (for RHD) |
![]() |
Align the matchmarks and install the steering wheel onto the steering column.
Install the nut.
Connect all the connectors to the spiral cable.
| 16. INSTALL STEERING WHEEL PAD ASSEMBLY (for Torx Type) |
![]() |
Support the steering pad with one hand as shown in the illustration.
Connect the 2 airbag connectors.
Connect the horn connector.
Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.
![]() |
Using a T30 "torx" driver, install the 2 screws.
| 17. INSTALL STEERING WHEEL PAD ASSEMBLY (for Pin Type) |
![]() |
Support the steering pad with one hand as shown in the illustration.
Connect the 2 airbag connectors.
Connect the horn connector.
Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.
Attach the 2 spring to steering pad.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).