Home › BODY › INSTRUMENT PANEL › UPPER INSTRUMENT PANEL

UPPER INSTRUMENT PANEL > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet codes in the table below.



B208880E02



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



3. REMOVE STEERING WHEEL PAD ASSEMBLY (for Torx Type)


B130245E01
  1. Straighten the front wheels.

  1. Using a T30 "torx" driver, loosen the 2 screws until the groove along each screw circumference catches on the screw case.



    B127893E01
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the 2 airbag connectors.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



4. REMOVE STEERING WHEEL PAD ASSEMBLY (for Pin Type)


    B217214
  1. Straighten the front wheels.

  1. Using a thin-bladed screwdriver, push open the spring clips and disengage the pins.



    B220978
  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the 2 airbag connectors.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



5. REMOVE STEERING WHEEL ASSEMBLY (for LHD)


    C132123E01
  1. Remove the nut and place matchmarks on the steering wheel and steering column.



    C132124E02
  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



6. REMOVE STEERING WHEEL ASSEMBLY (for RHD)


    C132125E01
  1. Remove the nut and place matchmarks on the steering wheel and steering column.



    C132126E01
  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B129872
  1. Using a screwdriver, detach the 4 clips and 6 claws, and then remove the instrument cluster finish panel.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE COMBINATION METER ASSEMBLY


B136780
  1. Remove the 2 screws.

  1. Pull the combination meter in the direction indicated by the arrow in the illustration to detach the 2 clips.

  1. Disconnect the connector and remove the combination meter.



9. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208365
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208366
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



11. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B133002
  1. Remove the 4 bolts.

  1. Detach the 4 clips and remove the stereo opening cover.



12. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


  1. w/o Stereo Opening Cover:

    1. Remove the 4 bolts.



    2. Pull the radio receiver to detach the 2 claws and 4 clips on the backside of the radio receiver.


      B219615

    3. Disconnect all connectors and remove the radio receiver with bracket.



  1. w/ Stereo Opening Cover:

    1. Remove the 4 bolts.



    2. Pull the radio receiver to detach the 2 claws and 4 clips on the backside of the radio receiver.


      B219616

    3. Disconnect all connectors and remove the radio receiver with bracket.



13. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for DVD)


  1. for 2AD-FTV, 2AD-FHV:

    1. Remove the 4 bolts.



    2. Pull the navigation receiver to detach the 2 claws and 4 clips on the backside of the navigation receiver.


      B220641

    3. Disconnect all the connectors and remove the navigation receiver.



  1. except 2AD-FTV, 2AD-FHV:

    1. Remove the 4 bolts.



    2. Pull the navigation receiver to detach 2 claws and 4 clips on the backside of the navigation receiver.


      B219744

    3. Disconnect all the connectors and remove the navigation receiver.



14. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System for HDD)
  1. Remove the 4 bolts.



  1. Pull the navigation receiver to detach the 2 claws and 4 clips on the backside of the navigation receiver.


    B219744

  1. Disconnect all connectors and remove the radio navigation with bracket.



15. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER


    B129890
  1. Using a moulding remover, detach the 5 clips and remove the instrument panel register.



16. REMOVE FRONT PILLAR GARNISH LH


    B129698
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



    B203236E01
  1. w/ Curtain Shield Airbag:

    1. Detach the 2 clips.

    2. Cut off the 2 clips.

    3. Detach the 3 claws and remove the garnish.

    4. Remove the 2 clips from the vehicle body.

      NOTICE:
      As the clips are cut, be sure to install new clips when installing the garnish.



    B114316
  1. Using a clip remover, remove the 4 wiring harness clamps.



    B065292E06
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



17. REMOVE FRONT PILLAR GARNISH RH


    B131251
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



    B203237E01
  1. w/ Curtain Shield Airbag:

    1. Detach the 2 clips.

    2. Cut off the 2 clips.

    3. Detach the 3 claws and remove the garnish.

    4. Remove the 2 clips from the vehicle body.

      NOTICE:
      As the clips are cut, be sure to install new clips when installing the garnish.



    B135443
  1. Using a clip remover, remove the 4 antenna cord clamps.



    B131254E01
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



18. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B129889E04
  1. Open the glove compartment door.

  1. Detach the claw from the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.



    B129888
  1. Open the door as much as possible.

  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



19. REMOVE UPPER INSTRUMENT PANEL


    B129886
  1. Remove the 2 bolts from the passenger airbag.

  1. Disconnect the passenger airbag connector.

  1. Remove the 2 bolts and 2 screws.

  1. Disconnect the connector and detach the clamp.



  1. Detach the 6 clips and 5 claws and remove the instrument panel.


    B208364