ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) > TERMINALS OF ECU |
| CHECK ENGINE SWITCH |

Disconnect the E31 switch connector.
Measure the resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (E31-5) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E31 switch connector.
Measure the resistance and voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E31-8) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| VC5 (E31-14) - AGND (E31-8) | R - BR | Power supply | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Press engine switch* | 4.6 to 5.4 V | |||
| CODE (E31-10) - AGND (E31-8) | W - BR | Demodulated signal of key code data | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Engine switch pressed and key held close to engine switch* | Pulse generation (see waveform 1) | |||
| TXCT (E31-9) - AGND (E31-8) | L - BR | Key code output signal | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Engine switch pressed and key held close to engine switch* | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | CODE (E31-10) - AGND (E31-8) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Engine switch pressed and key held close to engine switch* |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | TXCT (E31-9) - AGND (E31-8) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Engine switch pressed and key held close to engine switch* |
| CHECK ECU AGGREGATION BOX (CERTIFICATION ECU) |

Disconnect the E63 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| E (E63-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (E63-1) - E (E63-17) | R - W-B | +B power supply | Always | 11 to 14 V |
| IG (E63-18) - E (E63-17) | B - W-B | IG power supply | Engine switch off | Below 1 V |
Reconnect the E63 connector.
Measure the resistance and voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E63-40) - Body ground | BR - Body ground | Engine switch ground | Always | Below 1 Ω |
| VC5 (E63-30) - AGND (E63-40) | R - BR | Engine switch power supply | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Engine switch pressed* | 4.6 to 5.4 V | |||
| CODE (E63-9) - AGND (E63-40) | W - BR | Engine switch code input | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Engine switch pressed and key held close to engine switch* | Pulse generation (see waveform 1) | |||
| TXCT (E63-8) - AGND (E63-40) | L - BR | Engine switch TX output | Engine immobiliser system is set (key is not in cabin) | Below 1 V |
| Engine switch pressed and key held close to engine switch* | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | CODE (E63-9) - AGND (E63-40) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Engine switch pressed and key held close to engine switch* |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | TXCT (E63-8) - AGND (E63-40) |
| Tool Setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Engine switch pressed and key held close to engine switch* |
| CHECK ID CODE BOX |

Disconnect the E51 box connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (E51-8) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (E51-1) - GND (E51-8) | R - W-B | +B power supply | Always | 11 to 14 V |
Reconnect the E51 box connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| EFII (E51-5) - GND (E51-8) | LG - W-B | ECM input signal | Engine switch off | Below 1 V |
| Engine switch on (IG) | Pulse generation (see waveform 1) | |||
| EFIO (E51-6) - GND (E51-8) | P - W-B | ECM output signal | Engine switch off | Below 1 V |
| Engine switch on (IG) | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | EFII (E51-5) - GND (E51-8) |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Engine switch on (IG) |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | EFIO (E51-6) - GND (E51-8) |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Engine switch on (IG) |
| CHECK STEERING LOCK ACTUATOR (STEERING LOCK ECU) |

Disconnect the E6 ECU connector.
Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| SGND (E6-2) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| GND (E6-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| B (E6-7) - Body ground | L - Body ground | +B power supply | Always | 11 to 14 V |
| IG2 (E6-6) - Body ground | B - Body ground | IG power supply | Engine switch off | Below 1 V |
| Engine switch on (IG) | 11 to 14 V |
| CHECK ECM |

Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IMI (A12-16) - Body ground | P - Body ground | Transponder key ECU input signal | Engine switch off | Below 1 V |
| Engine switch on (IG) | Pulse generation (see waveform 1) | |||
| IMO (A12-15) - Body ground | LG - Body ground | Transponder key ECU output signal | Engine switch off | Below 1 V |
| Engine switch on (IG) | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | IMI (A12-16) - Body ground |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Engine switch on (IG) |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | IMO (A12-15) - Body ground |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Engine switch on (IG) |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |


Disconnect the ID, IE, E18 and E19 junction block connectors.
Measure the resistance and voltage of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND1 (IE-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND2 (E19-4) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| AM1 (E19-1) - Body ground | W -Body ground | +B power supply | Always | 11 to 14 V |
| AM2 (E19-6) - Body ground | W -Body ground | +B power supply | Always | 11 to 14 V |
| SSW1 (E19-10) - Body ground | W -Body ground | Engine switch | Engine switch off | 10 kΩ or higher |
| Engine switch on (IG) | Below 1 Ω | |||
| SSW2 (E19-9) - Body ground | B -Body ground | Engine switch | Engine switch off | 10 kΩ or higher |
| Engine switch on (IG) | Below 1 Ω | |||
| LIN1 (ID-9) - Body ground | V - Body ground | LIN communication line | Always | 10 kΩ or higher |