Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (LHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus line and +B when there is resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of DLC3 is below 6 kΩ.
  1. Short to +B
  2. Brake actuator (skid control ECU)*1
  3. ABS and traction actuator (skid control ECU)*2
  4. Power steering ECU
  5. Steering angle sensor*4
  6. Yaw rate sensor*2
  7. ECM
  8. Center airbag sensor assembly
  9. Combination meter ECU
  10. Air conditioning amplifier
  11. Main body ECU
  12. 4WD control ECU*3
  1. *1: w/ Anti-lock Brake System
  2. *2: w/ Vehicle Stability Control System
  3. *3: for 4WD
  4. *4: for 2WD (w/ Vehicle Stability Control System) and 4WD

WIRING DIAGRAM


C194056E07


C194057E06


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the main wire and the branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  3. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    1. w/ Navigation System (for HDD):
      After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or higher before disconnecting the cable from the negative (-) battery terminal.
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


NEXT


2.CHECK CAN BUS LINE FOR SHORT TO +B (DLC3 BRANCH WIRE)


    H100769E35
  1. Disconnect the E75 No. 2 junction connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


4.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR SIDE)


    H100769E35
  1. Disconnect the A51 No. 1 junction connector.

  1. Measure the resistance of the DLC3.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    Other
    A
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    Other
    A



B
Go to step 13
A


5.CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


6.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR, NO. 4 JUNCTION CONNECTOR SIDE)


    H100769E35
  1. Disconnect the E77 No. 3 junction connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 22
OK


7.CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


8.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR SIDE)


    H100769E35
  1. Disconnect the E76 No. 4 junction connector.

  1. Measure the resistance of the DLC3.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    Other
    A
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    Other
    A



B
Go to step 38
A


9.CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


10.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    C133164E64
  1. Disconnect the E77 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E77-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E77-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    Other
    A
    E77-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    B
    E77-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    Other
    A



B
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
A


11.CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


12.CHECK CAN BUS LINE FOR SHORT TO +B (CENTER AIRBAG SENSOR ASSEMBLY)


    H100769E35
  1. Disconnect the E49 center airbag sensor connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

13.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR)

NOTICE:
For vehicles without anti-lock brake system, go to "Check CAN Bus Line for Short to +B (No. 1 Junction Connector - ABS and Traction Actuator)".



    C133164E65
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A51-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A51-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 16
OK


14.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR)

NOTICE:
For vehicles without vehicle stability control system, go to "Check CAN Bus Line for Short to +B (No. 1 Junction Connector - ECM)".



    C133164E65
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A51-1 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A51-12 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 18
OK


15.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 1 JUNCTION CONNECTOR - ECM)


    C133164E66
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A51-2 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A51-13 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 20
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) 

16.CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


17.CHECK CAN BUS LINE FOR SHORT TO +B (BRAKE ACTUATOR)


    H100769E35
  1. Disconnect the A27 brake actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU) 

18.CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


19.CHECK CAN BUS LINE FOR SHORT TO +B (ABS AND TRACTION ACTUATOR)


    H100769E35
  1. Disconnect the A67 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ABS AND TRACTION ACTUATOR (CANH, CANL)
OK

REPLACE ABS AND TRACTION ACTUATOR (SKID CONTROL ECU) 

20.CONNECT CONNECTOR
  1. Reconnect the A51 No. 1 junction connector.


NEXT


21.CHECK CAN BUS LINE FOR SHORT TO +B (ECM)


    H100769E35
  1. Disconnect the A12 ECM connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (NO. 1 JUNCTION CONNECTOR - ECM)
OK

REPLACE ECM 

22.CONNECT CONNECTOR
  1. Reconnect the E77 No. 3 junction connector.


NEXT


23.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)

NOTICE:
For vehicles without vehicle stability control system, go to "Check CAN Bus Line for Short to +B (No. 2 Junction Connector - Steering Angle Sensor)".



    C133164E67
  1. Disconnect the E75 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-5 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-16 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 28
OK


24.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NOTICE:
For vehicles without 2WD with vehicle stability control system and 4WD, go to "Check CAN Bus Line for Short to +B (No. 2 Junction Connector - Power Steering ECU)".



    C163550E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-7 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-18 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 30
OK


25.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - POWER STEERING ECU)


    C133164E69
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-17 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 32
OK


26.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU)


    C133164E70
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-8 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-19 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 34
OK


27.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)


    C133164E71
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-15 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 36
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) 

28.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


29.CHECK CAN BUS LINE FOR SHORT TO +B (YAW RATE SENSOR)


    H100769E35
  1. Disconnect the K25 yaw rate sensor connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR 

30.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


31.CHECK CAN BUS LINE FOR SHORT TO +B (STEERING ANGLE SENSOR)


    H100769E35
  1. Disconnect the E95 steering angle sensor connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR 

32.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


33.CHECK CAN BUS LINE FOR SHORT TO +B (POWER STEERING ECU)


    H100769E35
  1. Disconnect the E21 power steering ECU connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU (CANH, CANL)
OK

REPLACE POWER STEERING ECU 

34.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


35.CHECK CAN BUS LINE FOR SHORT TO +B (MAIN BODY ECU)


    H100769E35
  1. Disconnect the E20 main body ECU connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) 

36.CONNECT CONNECTOR
  1. Reconnect the E75 No. 2 junction connector.


NEXT


37.CHECK CAN BUS LINE FOR SHORT TO +B (AIR CONDITIONING AMPLIFIER)


    H100769E35
  1. Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

    1. *1: for Automatic Air Conditioning System
    2. *2: for Manual Air Conditioning System

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER 

38.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without 4WD, go to "Check CAN Bus Line for Short to +B (No. 4 Junction Connector - Combination Meter ECU)".



    C133164E72
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-7 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-18 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 40
OK


39.CHECK CAN BUS LINE FOR SHORT TO +B (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C133164E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-5 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-16 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 42
OK


40.CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


41.CHECK CAN BUS LINE FOR SHORT TO +B (4WD CONTROL ECU)


    H100769E35
  1. Disconnect the E67 4WD control ECU connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU 

42.CONNECT CONNECTOR
  1. Reconnect the E76 No. 4 junction connector.


NEXT


43.CHECK CAN BUS LINE FOR SHORT TO +B (COMBINATION METER ECU)


    H100769E35
  1. Disconnect the E22 combination meter ECU connector.

  1. Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (CANH, CANL)
OK

REPLACE COMBINATION METER ECU