Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > Shift Paddle Switch Circuit

for Preparation Click here


DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM


C209058E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BODY GROUND)


    C203405E01
  1. Disconnect the spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E10-2 (ECC) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    C202155E02
  1. Remove the spiral cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SUP) - E10-9 (SUP)
    Always
    Below 1 Ω
    3 (SDN) - E10-10 (SDN)
    Always
    Below 1 Ω
    6 (ECC) - E10-2 (ECC)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable Sub-assembly)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.INSPECT TRANSMISSION SHIFT SWITCH ASSEMBLY (LH (-) AND RH (+))


    C202154E01
  1. Remove the transmission shift switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    SDN - ECC
    "-" shift paddle operated and held (down-shift)
    Below 2.5 Ω
    SDN - ECC
    "-" shift paddle not operated (down-shift)
    1 MΩ or higher
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    SUP - ECC
    "+" shift paddle operated and held (up-shift)
    Below 2.5 Ω
    SUP - ECC
    "+" shift paddle not operated (up-shift)
    1 MΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Transmission Shift Switch Assembly)
    *2
    for LH
    *3
    for RH



NG
REPLACE TRANSMISSION SHIFT SWITCH ASSEMBLY (Click here)
OK


4.INSPECT NO. 1 SWITCH WIRE


    C202153E01
  1. Disconnect the No. 1 switch wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    SDN - ECC
    "-" shift paddle operated and held (down-shift)
    Below 2.5 Ω
    SUP - ECC
    "+" shift paddle operated and held (up-shift)
    Below 2.5 Ω
    SDN - ECC
    "-" shift paddle not operated (down-shift)
    1 MΩ or higher
    SUP - ECC
    "+" shift paddle not operated (up-shift)
    1 MΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (No. 1 Switch Wire)



NG
REPLACE NO. 1 SWITCH WIRE (Click here)
OK


5.INSPECT STEERING PAD SWITCH ASSEMBLY


    C201603E03
  1. Disconnect the steering pad switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (SUP) - 6 (ECC)
    "+" shift paddle operated and held (up-shift)
    Below 2.5 Ω
    3 (SDN) - 6 (ECC)
    "-" shift paddle operated and held (down-shift)
    Below 2.5 Ω
    2 (SUP) - 6 (ECC)
    "+" shift paddle not operated (up-shift)
    1 MΩ or higher
    3 (SDN) - 6 (ECC)
    "-" shift paddle not operated (down-shift)
    1 MΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM)


    C200874E13
  1. Disconnect the ECM connectors.

  1. Disconnect the transmission control switch (shift lock control unit assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    B32-61 (SFTU) - Body ground
    "+" shift paddle operated and held (up-shift)
    Below 2.5 Ω
    A12-28 (SFTD) - Body ground
    "-" shift paddle operated and held (down-shift)
    Below 2.5 Ω
    B32-61 (SFTU) - Body ground
    "+" shift paddle not operated (up-shift)
    1 MΩ or higher
    A12-28 (SFTD) - Body ground
    "-" shift paddle not operated (down-shift)
    1 MΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)