Home › STEERING › STEERING COLUMN › STEERING LOCK SYSTEM

STEERING LOCK SYSTEM > Unable to Lock Steering Wheel

for Preparation Click here


WIRING DIAGRAM


C117908E02


INSPECTION PROCEDURE

HINT:
When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:
Before starting the inspection, with the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.

1.CHECK DTC (CERTIFICATION ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.

    OK:
    No DTCs related to the main body ECU are output.



NG
GO TO RELEVANT DTC
OK


2.CHECK DTC (MAIN BODY ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Read the DTCs of the main body ECU by following the prompts displayed on the intelligent tester.

    OK:
    No DTCs related to the main body ECU are output.



NG
GO TO RELEVANT DTC
OK


3.READ VALUE USING DATA LIST (CERTIFICATION ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Within 10 seconds after the engine is started, read the Data List menu of the certification ECU, and check the steering lock command reception record.

    Certification ECU 
    Item
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Lock / Unlock Receive
    Steering lock command reception record / YES or NO
    YES: Steering lock / unlock signal received
    NO: Steering lock / unlock signal not received
    -

    OK:
    YES is displayed on the intelligent tester screen.



NG
Go to step 5
OK


4.CHECK STEERING LOCK ACTUATOR
B128061E01
  1. Turn the engine switch on (IG).

  1. Turn the engine switch off.

  1. Immediately after opening the driver door, inspect the voltage between terminals E6-3 (IGE) and E6-2 (SGND) of the steering lock actuator.
    Result 
    Result
    Proceed to
    Immediately after opening door, condition that measurement is 1 V or less occurs
    A
    Measurement is 11 to 14 V, and measurement never becomes 1 V or less
    B



B
REPAIR OR REPLACE HARNESS AND CONNECTOR
A

REPLACE STEERING LOCK ACTUATOR ASSEMBLY 

5.CHECK STEERING LOCK FUNCTION
  1. Open the front passenger side door.

  1. Lock the doors using the wireless remote door lock key.

  1. Check that no doors are locked and the steering lock does not operate.

    OK:
    No doors are locked and steering lock is not locked.



NG
GO TO LIGHTING SYSTEM (DOOR COURTESY SWITCH CIRCUIT)
OK


6.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Check the Data List and read the value displayed on the intelligent tester.

    Certification ECU 
    Item
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    S Code Check
    S code match record / NG or OK
    NG: S code not matched
    OK: S code matched
    -

    OK:
    OK is displayed on the intelligent tester screen.



OK
Go to step 8
NG


7.CHECK OPERATION OF ID CODE BOX
  1. Replace the ID code box with a normally functioning or new one.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Check the Data List and read the value displayed on the intelligent tester.

    Certification ECU 
    Item
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    S Code Check
    S code match record / NG or OK
    NG: S code not matched
    OK: S code matched
    -

    OK:
    OK is displayed on the intelligent tester screen.



OK
REPLACE ID CODE BOX
NG

REPLACE CERTIFICATION ECU 

8.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Check the Data List and read the value displayed on the intelligent tester.

    Certification ECU 
    Item
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    L Code Check
    L code match record / NG or OK
    NG: L code not matched
    OK: L code matched
    -

    OK:
    OK is displayed on the intelligent tester screen.



OK
Go to step 10
NG


9.CHECK OPERATION OF ID CODE BOX
  1. Replace the ID code box with a normally functioning or new one.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and press the intelligent tester main switch ON.

  1. Check the Data List and read the value displayed on the intelligent tester.

    Certification ECU 
    Item
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    L Code Check
    L code match record / NG or OK
    NG: L code not matched
    OK: L code matched
    -

    OK:
    OK is displayed on the intelligent tester screen.



OK
REPLACE ID CODE BOX
NG

REPLACE STEERING LOCK ACTUATOR ASSEMBLY 

10.CHECK OPERATION OF STEERING LOCK ACTUATOR
  1. Replace the steering lock actuator assembly with a normally functioning or new one.

  1. With the clutch pedal depressed, turn the engine switch on (IG).

  1. Check whether the steering lock can be released by turning the steering wheel, and check that the engine starts.

    OK:
    Steering lock is released and engine starts.



OK
REPLACE STEERING LOCK ACTUATOR ASSEMBLY
NG

REPLACE CERTIFICATION ECU