ENGINE IMMOBILISER SYSTEM (w/o Entry and Start System) > TERMINALS OF ECU |
| CHECK TRANSPONDER KEY AMPLIFIER |

Disconnect the E8 amplifier connector.
Measure the resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E8-7) - Body ground | R - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E8 amplifier connector.
Measure the resistance and voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E8-7) - Body ground | R - Body ground | Ground | Always | Below 1 Ω |
| VC5 (E8-1) - AGND (E8-7) | B - R | Power source | No key is in ignition key cylinder | Below 1 V |
| Key inserted | 4.6 to 5.4 V | |||
| CODE (E8-4) - AGND (E8-7) | P - R | Demodulated signal of key code data | No key is in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (see waveform 1) | |||
| TXCT (E8-5) - AGND (E8-7) | G - R | Key code output signal | No key is in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | CODE (E8-4) - AGND (E8-7) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | TXCT (E8-5) - AGND (E8-7) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Key inserted |
| CHECK TRANSPONDER KEY ECU |

Disconnect the E50 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| GND (E50-16) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| +B (E50-1) - GND (E50-16) | R - W-B | Battery | Always | 11 to 14 V |
| IG (E50-2) - GND (E50-16) | B - W-B | Ignition switch | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
Reconnect the E50 ECU connector.
Measure the resistance and voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AGND (E50-5) - GND (E50-16) | R - W-B | Amplifier ground circuit | Always | Below 1 Ω |
| KSW (E50-3) - GND (E50-16) | L - W-B | Unlock warning switch | No key is in ignition key cylinder | 11 to 14 V |
| Key inserted | Below 1 V | |||
| VC5 (E50-14) - AGND (E50-5) | B - R | Power source | No key is in ignition key cylinder | Below 1 V |
| Key inserted | 4.6 to 5.4 V | |||
| TXCT (E50-4) - AGND (E50-5) | G - R | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (see waveform 1) | |||
| CODE (E50-15) - AGND (E50-5) | P - R | Transponder key amplifier communication signal | No key is in ignition key cylinder | Below 1 V |
| Key inserted | Pulse generation (see waveform 2) | |||
| EFIO (E50-13) - GND (E50-16) | P - W-B | ECM output signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (see waveform 3) | |||
| EFII (E50-12) - GND (E50-16) | LG - W-B | ECM input signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (see waveform 4) | |||
| IND (E50-8)- GND (E50-16) | Y - W-B | Security indicator light signal | Engine immobiliser system SET | 3 to 5 V |
| Engine immobiliser system UNSET | Below 1 V | |||
| D (E50-9) - GND (E50-16) | W - W-B | Diagnosis tester communication | Ignition switch ON | Pulse generation |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | TXCT (E50-4) - AGND (E50-5) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | CODE (E50-15) - AGND (E50-5) |
| Tool Setting | 5 V/DIV., 20 msec./DIV. |
| Condition | Key inserted |
![]() |
Using an oscilloscope, check the waveform 3.
| Item | Content |
| Symbols (Terminal No.) | EFIO (E50-13) - GND (E50-16) |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Ignition switch ON |
![]() |
Using an oscilloscope, check the waveform 4.
| Item | Content |
| Symbols (Terminal No.) | EFII (E50-12) - GND (E50-16) |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Ignition switch ON |
| CHECK ECM |

Measure the resistance and voltage of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IMI (A12-16) - Body ground | P - Body ground | Transponder key ECU input signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (see waveform 1) | |||
| IMO (A12-15) - Body ground | LG - Body ground | Transponder key ECU output signal | Ignition switch off | Below 1 V |
| Ignition switch ON | Pulse generation (see waveform 2) |
![]() |
Using an oscilloscope, check the waveform 1.
| Item | Content |
| Symbols (Terminal No.) | IMI (A12-16) - Body ground |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Ignition switch ON |
![]() |
Using an oscilloscope, check the waveform 2.
| Item | Content |
| Symbols (Terminal No.) | IMO (A12-15) - Body ground |
| Tool Setting | 10 V/DIV., 100 msec./DIV. |
| Condition | Ignition switch ON |