CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (RHD Models) |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. |
|


| 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
| NEXT | |
| 2.CHECK CAN BUS LINES FOR SHORT CIRCUIT (DLC3 BRANCH WIRE) |
![]() |
Disconnect the E89 No. 4 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 3.CONNECT CONNECTOR |
Reconnect the E89 No. 4 junction connector.
| NEXT | |
| 4.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the A51 No. 1 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 108 to 132 Ω | B |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 5.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the E87 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E87-4 (CANH) - E87-15 (CANL) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 6.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 7.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the E87 No. 2 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 108 to 132 Ω | B |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 8.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR) |
![]() |
Disconnect the E77 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E77-3 (CANH) - E77-14 (CANL) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 9.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 10.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR, NO. 3 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the E77 No. 3 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 108 to 132 Ω | B |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 11.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR) |
![]() |
Disconnect the E89 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E89-6 (CANH) - E89-17 (CANL) | Ignition switch off | 6 kΩ or higher |
|
| ||||
| OK | |
| 12.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
Reconnect the E89 No. 4 junction connector.
| NEXT | |
| 13.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
![]() |
Disconnect the E88 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E88-6 (CANH) - E88-17 (CANL) | Ignition switch off | Below 1 Ω | B |
| E88-6 (CANH) - E88-17 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 14.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E88-7 (CANH) - E88-18 (CANL) | Ignition switch off | Below 1 Ω | B |
| E88-7 (CANH) - E88-18 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 15.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E88-5 (CANH) - E88-16 (CANL) | Ignition switch off | Below 1 Ω | B |
| E88-5 (CANH) - E88-16 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | ||
| ||
| 16.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 17.CHECK CAN BUS LINES FOR SHORT CIRCUIT (4WD CONTROL ECU) |
![]() |
Disconnect the E67 4WD control ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 18.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 19.CHECK CAN BUS LINES FOR SHORT CIRCUIT (STEERING ANGLE SENSOR) |
![]() |
Disconnect the E95 steering angle sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 20.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 21.CHECK CAN BUS LINES FOR SHORT CIRCUIT (COMBINATION METER ECU) |
![]() |
Disconnect the E22 combination meter ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 22.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| A51-1 (CANH) - A51-12 (CANL) | Ignition switch off | Below 1 Ω | B |
| A51-1 (CANH) - A51-12 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 23.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| A51-1 (CANH) - A51-12 (CANL) | Ignition switch off | Below 1 Ω | B |
| A51-1 (CANH) - A51-12 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 24.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| A51-2 (CANH) - A51-13 (CANL) | Ignition switch off | Below 1 Ω | B |
| A51-2 (CANH) - A51-13 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | ||
| ||
| 25.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 26.CHECK CAN BUS LINES FOR SHORT CIRCUIT (BRAKE ACTUATOR) |
![]() |
Disconnect the A27 brake actuator (skid control ECU) connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 27.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 28.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ABS AND TRACTION ACTUATOR) |
![]() |
Disconnect the A67 ABS and traction actuator (skid control ECU) connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 29.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 30.CHECK CAN BUS LINES FOR SHORT CIRCUIT (ECM) |
![]() |
Disconnect the A12 ECM connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 108 to 132 Ω |
|
| ||||
| OK | ||
| ||
| 31.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E87-2 (CANH) - E87-13 (CANL) | Ignition switch off | Below 1 Ω | B |
| E87-2 (CANH) - E87-13 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 32.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E87-5 (CANH) - E87-16 (CANL) | Ignition switch off | Below 1 Ω | B |
| E87-5 (CANH) - E87-16 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | ||
| ||
| 33.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 34.CHECK CAN BUS LINES FOR SHORT CIRCUIT (YAW RATE SENSOR) |
![]() |
Disconnect the K25 yaw rate sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 35.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 36.CHECK CAN BUS LINES FOR SHORT CIRCUIT (MAIN BODY ECU) |
![]() |
Disconnect the E20 main body ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 37.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E77-2 (CANH) - E77-13 (CANL) | Ignition switch off | Below 1 Ω | B |
| E77-2 (CANH) - E77-13 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 38.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E77-4 (CANH) - E77-15 (CANL) | Ignition switch off | Below 1 Ω | B |
| E77-4 (CANH) - E77-15 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 39.CHECK CAN BUS LINES FOR SHORT CIRCUIT (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E77-1 (CANH) - E77-12 (CANL) | Ignition switch off | Below 1 Ω | B |
| E77-1 (CANH) - E77-12 (CANL) | Ignition switch off | Other | A |
|
| ||||
| A | ||
| ||
| 40.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 41.CHECK CAN BUS LINES FOR SHORT CIRCUIT (AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the E41*1 or E42*2 air conditioning amplifier connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 42.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 43.CHECK CAN BUS LINES FOR SHORT CIRCUIT (POWER STEERING ECU) |
![]() |
Disconnect the E21 power steering ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||
| 44.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 45.CHECK CAN BUS LINES FOR SHORT CIRCUIT (CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the E49 center airbag sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-14 (CANL) | Ignition switch off | 54 to 69 Ω |
|
| ||||
| OK | ||
| ||