CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to GND (RHD Models) |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of DLC3 is below 200 Ω. |
|


| 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
| NEXT | |
| 2.CHECK CAN BUS LINE FOR SHORT TO GND (DLC3 BRANCH WIRE) |
![]() |
Disconnect the E89 No. 4 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 3.CONNECT CONNECTOR |
Reconnect the E89 No. 4 junction connector.
| NEXT | |
| 4.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the A51 No. 1 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | Other | A |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 5.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 6.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR SIDE) |
![]() |
Disconnect the E87 No. 2 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | Other | A |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 7.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 8.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR, NO. 2 JUNCTION CONNECTOR, NO. 3 JUNCTION CONNECTOR) |
![]() |
Disconnect the E77 No. 3 junction connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | Other | A |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher | B |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | Other | A |
|
| ||||
| A | |
| 9.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 10.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 4 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
![]() |
Disconnect the E88 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E88-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E88-17 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 11.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 4 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E88-7 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E88-18 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 12.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 4 JUNCTION CONNECTOR - COMBINATION METER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E88-5 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E88-16 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 13.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 14.CHECK CAN BUS LINE FOR SHORT TO GND (4WD CONTROL ECU) |
![]() |
Disconnect the E67 4WD control ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 15.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 16.CHECK CAN BUS LINE FOR SHORT TO GND (STEERING ANGLE SENSOR) |
![]() |
Disconnect the E95 steering angle sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 17.CONNECT CONNECTOR |
Reconnect the E88 No. 4 junction connector.
| NEXT | |
| 18.CHECK CAN BUS LINE FOR SHORT TO GND (COMBINATION METER ECU) |
![]() |
Disconnect the E22 combination meter ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 19.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR - BRAKE ACTUATOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A51-1 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| A51-12 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 20.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR - ABS AND TRACTION ACTUATOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A51-1 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| A51-12 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 21.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 1 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A51-2 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| A51-13 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 22.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 23.CHECK CAN BUS LINE FOR SHORT TO GND (BRAKE ACTUATOR) |
![]() |
Disconnect the A27 brake actuator (skid control ECU) connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 24.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 25.CHECK CAN BUS LINE FOR SHORT TO GND (ABS AND TRACTION ACTUATOR) |
![]() |
Disconnect the A67 ABS and traction actuator (skid control ECU) connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 26.CONNECT CONNECTOR |
Reconnect the A51 No. 1 junction connector.
| NEXT | |
| 27.CHECK CAN BUS LINE FOR SHORT TO GND (ECM) |
![]() |
Disconnect the A12 ECM connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 28.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E87-2 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E87-13 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 29.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E87-5 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E87-16 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 30.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 31.CHECK CAN BUS LINE FOR SHORT TO GND (YAW RATE SENSOR) |
![]() |
Disconnect the K25 yaw rate sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 32.CONNECT CONNECTOR |
Reconnect the E87 No. 2 junction connector.
| NEXT | |
| 33.CHECK CAN BUS LINE FOR SHORT TO GND (MAIN BODY ECU) |
![]() |
Disconnect the E20 main body ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 34.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E77-2 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E77-13 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 35.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 3 JUNCTION CONNECTOR - POWER STEERING ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E77-4 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E77-15 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 36.CHECK CAN BUS LINE FOR SHORT TO GND (NO. 3 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E77-1 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E77-12 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 37.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 38.CHECK CAN BUS LINE FOR SHORT TO GND (AIR CONDITIONING AMPLIFIER) |
![]() |
Disconnect the E41*1 or E42*2 air conditioning amplifier connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 39.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 40.CHECK CAN BUS LINE FOR SHORT TO GND (POWER STEERING ECU) |
![]() |
Disconnect the E21 power steering ECU connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 41.CONNECT CONNECTOR |
Reconnect the E77 No. 3 junction connector.
| NEXT | |
| 42.CHECK CAN BUS LINE FOR SHORT TO GND (CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the E49 center airbag sensor connector.
Measure the resistance of the DLC3.
| Tester Connection | Switch Condition | Specified Condition |
| E16-6 (CANH) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
| E16-14 (CANL) - E16-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||