AUDIO AND VISUAL SYSTEM > Speaker Circuit |

| 1.CHECK SPEAKER |
Check that the speaker sounds.
| Result | Proceed to |
| Front No. 1 speaker does not operate | A |
| Front No. 2 speaker does not operate | B |
| Rear No. 1 speaker does not operate | C |
| All speakers do not operate | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the front No. 2 speaker sounds.
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Disconnect the H6 or G7 receiver connector.
Measure the resistance of the speaker.
| Tester Connection | Specified Condition |
| 1 (-) - 2 (TWL-)*1 or (TWR-)*2 | Below 1 Ω |
| 3 (+) - 4 (TWL+)*1 or (TWR+)*2 | Below 1 Ω |
| 1 (-) - Body ground | 10 kΩ or higher |
| 3 (+) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (FRONT NO. 1 SPEAKER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the H1 and H6, or G1 and G7 connectors.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H1-1 - H6-3 (+) | Below 1 Ω |
| H1-1 - Body ground | 10 kΩ or higher |
| H1-2 - H6-1 (-) | Below 1 Ω |
| H1-2 - Body ground | 10 kΩ or higher |
| G1-1 - G7-3 (+) | Below 1 Ω |
| G1-1 - Body ground | 10 kΩ or higher |
| G1-2 - G7-1 (-) | Below 1 Ω |
| G1-2 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK WIRE HARNESS (RADIO RECEIVER - FRONT NO. 2 SPEAKER) |
![]() |
Disconnect the E90 receiver connector.
Disconnect the H6 or G7 speaker connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E90-1 (FR+) - G7-4 (TWR+) | Below 1 Ω |
| E90-5 (FR-) - G7-2 (TWR-) | Below 1 Ω |
| E90-1 (FR+) - Body ground | 10 kΩ or higher |
| E90-5 (FR-) - Body ground | 10 kΩ or higher |
| E90-2 (FL+) - H6-4 (TWL+) | Below 1 Ω |
| E90-6 (FL-) - H6-2 (TWL-) | Below 1 Ω |
| E90-2 (FL+) - Body ground | 10 kΩ or higher |
| E90-6 (FL-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Check that the malfunction disappears when another speaker in good condition is installed.
|
| ||||
| NG | ||
| ||
| 7.CHECK WIRE HARNESS (RADIO RECEIVER - REAR NO. 1 SPEAKER) |
![]() |
Disconnect the E91 receiver connector.
Disconnect the J2 or I2 receiver connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E91-1 (RR+) - I2-1 | Below 1 Ω |
| E91-3 (RR-) - I2-2 | Below 1 Ω |
| E91-1 (RR+) - Body ground | 10 kΩ or higher |
| E91-3 (RR-) - Body ground | 10 kΩ or higher |
| E91-2 (RL+) - J2-1 | Below 1 Ω |
| E91-6 (RL-) - J2-2 | Below 1 Ω |
| E91-2 (RL+) - Body ground | 10 kΩ or higher |
| E91-6 (RL-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT REAR NO. 1 SPEAKER ASSEMBLY |
Check the rear No. 1 speaker (Click here).
|
| ||||
| OK | ||
| ||