ENTRY AND START SYSTEM > Driver Side Door Entry Unlock Function does not Operate |

| 1.CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
|
| ||||
| OK | |
| 2.CHECK MANUAL DOOR UNLOCK OPERATION |
Check that all the doors unlock when the door control switch (for manual operation) is turned to UNLOCK.
|
| ||||
| OK | |
| 3.CHECK WIRELESS DOOR LOCK CONTROL OPERATION |
Check that the wireless door lock and unlock functions operate normally (Click here).
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY LIGHT SWITCH) |
Check the Data List to confirm the operation of the door courtesy light switch (driver side).
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver side door courtesy light switch signal ON / OFF | ON: Driver side door is open OFF: Driver side door is closed | - |
|
| ||||
| OK | |
| 5.READ VALUE USING INTELLIGENT TESTER (LOCK POSITION SWITCH) |
Check the Data List for proper functioning of the door lock position switch (driver side).
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| D-Door Lock Pos SW | Driver side door lock position switch signal / ON or OFF | ON: Door is unlocked OFF: Door is locked | - |
|
| ||||
| OK | |
| 6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER SIDE SELECT) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the door electrical key oscillator operates.
| Item | Test Details | Diagnostic Note |
| D-Seat Select | Driver side electrical key oscillator ON / OFF | - |
|
| ||||
| OK | |
| 7.READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR) |
With "D-Seat Select" ON, check the Data List to confirm the operation of the touch sensor (driver side).
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| D-Door Touch Sensor | Driver side door touch sensor / ON or OFF | ON: Sensor is touched OFF: Sensor is not touched | - |
|
| ||||
| OK | |
| 8.CHECK ECU AGGREGATION BOX (CERTIFICATION ECU) |
Temporarily replace the ECU aggregation box (certification ECU) with a new or normally functioning one.
Check that the entry unlock function operates normally (Click here).
|
| ||||
| OK | ||
| ||
| 9.CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Driver Side) |
![]() |
Measure the voltage of the oscillator.
| Tester Connection | Condition | Specified Condition |
| 4 (SEL) - Body ground | During Active Test | Below 1 V |
| 6 (SENS) - Body ground | Touch sensor is touched during Active Test | Below 1 V |
| Touch sensor is not touched during Active Test | 10 to 14 V |
|
| ||||
| NG | |
| 10.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA) |
![]() |
Disconnect the Z2*1 or Y2*2 oscillator connector.
Disconnect the Z1*1 or Y1*2 antenna connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| Z2-2 (SGT) - Z1-6 (SGT) | Below 1 Ω |
| Z2-3 (ANT1) - Z1-5 (ANT1) | |
| Z2-8 (ANT2) - Z1-2 (ANT2) | |
| Z2-9 (TRG-) - Z1-1 (TRG-) | |
| Z2-2 (SGT) or Z1-6 (SGT) - Body ground | 10 kΩ or higher |
| Z2-3 (ANT1) or Z1-5 (ANT1) - Body ground | |
| Z2-8 (ANT2) or Z1-2 (ANT2) - Body ground | |
| Z2-9 (TRG-) or Z1-1 (TRG-) - Body ground |
| Tester Connection | Specified Condition |
| Y2-2 (SGT) - Y1-6 (SGT) | Below 1 Ω |
| Y2-3 (ANT1) - Y1-5 (ANT1) | |
| Y2-8 (ANT2) - Y1-2 (ANT2) | |
| Y2-9 (TRG-) - Y1-1 (TRG-) | |
| Y2-2 (SGT) or Y1-6 (SGT) - Body ground | 10 kΩ or higher |
| Y2-3 (ANT1) or Y1-5 (ANT1) - Body ground | |
| Y2-8 (ANT2) or Y1-2 (ANT2) - Body ground | |
| Y2-9 (TRG-) or Y1-1 (TRG-) - Body ground |
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() |
Disconnect the E63 ECU connector.
Disconnect the Z2*1 or Y2*2 oscillator connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E63-5 (SEL1) - Z2-4 (SEL) | Below 1 Ω |
| E63-22 (SEN1) - Z2-6 (SENS) | |
| E63-33 (CLG1) - Z2-10 (CLG) | |
| E63-34 (CG1B) - Z2-5 (CLGB) | |
| E63-5 (SEL1) or Z2-4 (SEL) - Body ground | 10 kΩ or higher |
| E63-22 (SEN1) or Z2-6 (SENS) - Body ground | |
| E63-33 (CLG1) or Z2-10 (CLG) - Body ground | |
| E63-34 (CG1B) or Z2-5 (CLGB) - Body ground |
| Tester Connection | Specified Condition |
| E63-5 (SEL1) - Y2-4 (SEL) | Below 1 Ω |
| E63-22 (SEN1) - Y2-6 (SENS) | |
| E63-33 (CLG1) - Y2-10 (CLG) | |
| E63-34 (CG1B) - Y2-5 (CLGB) | |
| E63-5 (SEL1) or Y2-4 (SEL) | 10 kΩ or higher |
| E63-22 (SEN1) or Y2-6 (SENS) | |
| E63-33 (CLG1) or Y2-10 (CLG) | |
| E63-34 (CG1B) or Y2-5 (CLGB) |
|
| ||||
| OK | ||
| ||