Home › BODY ELECTRICAL › DOOR LOCK › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > Driver Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

Neither the entry lock nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (driver side), 2) the entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.

WIRING DIAGRAM


B133518E01


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. By following the tester screen display, check whether any DTCs are output.

    OK:
    No DTC output.



NG
Go to DIAGNOSTIC TROUBLE CODE CHART
OK


2.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION
  1. Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

    OK:
    All doors can be locked and unlocked with door control switch.



NG
Go to POWER DOOR LOCK CONTROL SYSTEM
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

    Certification ECU: 
    Item
    Test Details
    Diagnostic Note
    D-Seat Outside Transmitter
    Driver side door electrical key oscillator ON / OFF
    -

    OK:
    When key is brought close to door oscillator that is ON, indicator light on key illuminates.



OK
REPLACE ECU AGGREGATION BOX (CERTIFICATION ECU)
NG


4.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)
B108060E29
  1. Disconnect the E63 ECU connector.

  1. Disconnect the Z2*1 or Y2*2 oscillator connector.

  1. Measure the resistance of the wire harness side connectors.

    HINT:
    *1: for LHD
    *2: for RHD


    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    E63-33 (CLG1) - Z2-10 (CLG)
    Below 1 Ω
    E63-34 (CG1B) - Z2-5 (CLGB)
    E63-33 (CLG1) or Z2-10 (CLG) - Body ground
    10 kΩ or higher
    E63-34 (CG1B) or Z2-5 (CLGB) - Body ground
    for RHD:
    Tester Connection
    Specified Condition
    E63-33 (CLG1) - Z2-10 (CLG)
    Below 1 Ω
    E63-34 (CG1B) - Z2-5 (CLGB)
    E63-33 (CLG1) or Z2-10 (CLG) - Body ground
    10 kΩ or higher
    E63-34 (CG1B) or Z2-5 (CLGB) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)
B108040E30
  1. Disconnect the Z2*1 or Y2*2 oscillator connector.

  1. Disconnect the Z1*1 or Y1*2 antenna connector.

  1. Measure the resistance of the wire harness side connectors.

    HINT:
    *1: for LHD
    *2: for RHD


    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    Z2-2 (SGT) - Z1-6 (SGT)
    Below 1 Ω
    Z2-3 (ANT1) - Z1-5 (ANT1)
    Z2-8 (ANT2) - Z1-2 (ANT2)
    Z2-9 (TRG-) - Z1-1 (TRG-)
    Z2-2 (SGT) or Z1-6 (SGT) - Body ground
    10 kΩ or higher
    Z2-3 (ANT1) or Z1-5 (ANT1) - Body ground
    Z2-8 (ANT2) or Z1-2 (ANT2) - Body ground
    Z2-9 (TRG-) or Z1-1 (TRG-) - Body ground
    for RHD:
    Tester Connection
    Specified Condition
    Y2-2 (SGT) - Y1-6 (SGT)
    Below 1 Ω
    Y2-3 (ANT1) - Y1-5 (ANT1)
    Y2-8 (ANT2) - Y1-2 (ANT2)
    Y2-9 (TRG-) - Y1-1 (TRG-)
    Y2-2 (SGT) or Y1-6 (SGT) - Body ground
    10 kΩ or higher
    Y2-3 (ANT1) or Y1-5 (ANT1) - Body ground
    Y2-8 (ANT2) or Y1-2 (ANT2) - Body ground
    Y2-9 (TRG-) or Y1-1 (TRG-) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
B127160E03
  1. Disconnect the Z2*1 or Y2*2 oscillator connector.

  1. Measure the resistance and voltage of the wire harness side connector.

    HINT:
    *1: for LHD
    *2: for RHD


    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    Z2-7 (GND) - Body ground
    Below 1 Ω
    for RHD:
    Tester Connection
    Specified Condition
    Y2-7 (GND) - Body ground
    Below 1 Ω


    Standard voltage:
    for LHD:
    Tester Connection
    Specified Condition
    Z2-1 (+B) - Body ground
    10 to 14 V
    for RHD:
    Tester Connection
    Specified Condition
    Y2-1 (+B) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
B127161E03
  1. Disconnect the Z1*1 or Y1*2 antenna connector.

  1. Disconnect the E63 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    HINT:
    *1: for LHD
    *2: for RHD


    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    Z1-3 (TRG+) - E63-3 (TSW1)
    Below 1 Ω
    Z1-3 (TRG+) or E63-3 (TSW1) - Body ground
    10 kΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    Y1-3 (TRG+) - E63-3 (TSW1)
    Below 1 Ω
    Y1-3 (TRG+) or E63-3 (TSW1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
  1. Temporarily replace the front door outside handle (electrical key antenna) with a new or normally functioning one.

  1. Check that the entry lock and unlock functions operate normally (Click here).

    OK:
    Entry lock and unlock functions operate normally.



OK
END (ELECTRICAL KEY ANTENNA IS DEFECTIVE)
NG


9.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Temporarily replace the door electrical key oscillator (driver side) with a new or normally functioning one.

  1. Check that the entry lock and unlock functions operate normally.

    OK:
    Entry lock and unlock functions operate normally.



NG
REPLACE ECU AGGREGATION BOX (CERTIFICATION ECU)
OK

END (DOOR KEY OSCILLATOR IS DEFECTIVE)