ENTRY AND START SYSTEM > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate |

| 1.CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
|
| ||||
| OK | |
| 2.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION |
Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.
| Item | Test Details | Diagnostic Note |
| P-Seat Outside Transmitter | Front passenger side door electrical key oscillator ON / OFF | - |
|
| ||||
| NG | |
| 4.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() |
Disconnect the E63 ECU connector.
Disconnect the Y2*1 or Z2*2 oscillator connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E63-25 (CLG2) - Y2-10 (CLG) | Below 1 Ω |
| E63-36 (CG2B) - Y2-5 (CLGB) | |
| E63-25 (CLG2) or Y2-10 (CLG) - Body ground | 10 kΩ or higher |
| E63-36 (CG2B) or Y2-5 (CLGB) - Body ground |
| Tester Connection | Specified Condition |
| E63-25 (CLG2) - Z2-10 (CLG) | Below 1 Ω |
| E63-36 (CG2B) - Z2-5 (CLGB) | |
| E63-25 (CLG2) or Z2-10 (CLG) - Body ground | 10 kΩ or higher |
| E63-36 (CG2B) or Z2-5 (CLGB) - Body ground |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA) |
![]() |
Disconnect the Y2*1 or Z2*2 oscillator connector.
Disconnect the Y1*1 or Z1*2 antenna connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| Y2-2 (SGT) - Y1-6 (SGT) | Below 1 Ω |
| Y2-3 (ANT1) - Y1-5 (ANT1) | |
| Y2-8 (ANT2) - Y1-2 (ANT2) | |
| Y2-9 (TRG-) - Y1-1 (TRG-) | |
| Y2-2 (SGT) or Y1-6 (SGT) - Body ground | 10 kΩ or higher |
| Y2-3 (ANT1) or Y1-5 (ANT1) - Body ground | |
| Y2-8 (ANT2) or Y1-2 (ANT2) - Body ground | |
| Y2-9 (TRG-) or Y1-1 (TRG-) - Body ground |
| Tester Connection | Specified Condition |
| Z2-2 (SGT) - Z1-6 (SGT) | Below 1 Ω |
| Z2-3 (ANT1) - Z1-5 (ANT1) | |
| Z2-8 (ANT2) - Z1-2 (ANT2) | |
| Z2-9 (TRG-) - Z1-1 (TRG-) | |
| Z2-2 (SGT) or Z1-6 (SGT) - Body ground | 10 kΩ or higher |
| Z2-3 (ANT1) or Z1-5 (ANT1) - Body ground | |
| Z2-8 (ANT2) or Z1-2 (ANT2) - Body ground | |
| Z2-9 (TRG-) or Z1-1 (TRG-) - Body ground |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND) |
![]() |
Disconnect the Y2*1 or Z2*2 oscillator connector.
Measure the resistance and voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
| Y2-7 (GND) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| Z2-7 (GND) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| Y2-1(+B) - Y2-7 (GND) | 10 to 14 V |
| Tester Connection | Specified Condition |
| Z2-1(+B) - Z2-7 (GND) | 10 to 14 V |
|
| ||||
| OK | |
| 7.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU) |
![]() |
Disconnect the Y2*1 or Z2*2 oscillator connector.
Disconnect the E63 ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| Y2-3 (TRG+) - E63-4 (TSW2) | Below 1 Ω |
| Y2-3 (TRG+) - E63-4 (TSW2) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| Z2-3 (TRG+) - E63-4 (TSW2) | Below 1 Ω |
| Z2-3 (TRG+) - E63-4 (TSW2) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION) |
Check that the entry lock and unlock functions operate normally (Click here).
|
| ||||
| NG | |
| 9.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Temporarily replace the door electrical key oscillator (passenger side) with a new or normally functioning one.
Check that the entry lock and unlock functions operate normally.
|
| ||||
| OK | ||
| ||