WIPER AND WASHER SYSTEM (w/ Rain Sensor) > TERMINALS OF ECU |
| CHECK AUTO WIPER RELAY |

Disconnect the E66 relay connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IG (E66-12) - Body ground | L - Body ground | IG signal circuit | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| WIG (E66-23) - Body ground | L - Body ground | WIG signal circuit | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| W (E66-4) - Body ground | W - Body ground | Front washer switch circuit | Front washer switch is ON | Below 1 Ω |
| Front washer switch is OFF | 10 kΩ or higher | |||
| E (E66-26) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the E66 relay connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| +2S (E66-1) - Body ground | B - Body ground | Front wiper LO speed signal circuit | Ignition switch on (IG), front wiper switch LO | 10 to 14 V |
| Ignition switch on (IG), front wiper switch except LO | Below 1 V | |||
| +2 (E66-3) - Body ground | R - Body ground | Front wiper motor HI speed signal circuit | Front wiper motor is in HI operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V | |||
| C1 (E66-17) - C0 (E66-16) | GR - L | IG signal circuit | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| W (E66-4) - Body ground | W - Body ground | Front washer motor circuit | Front washer switch is ON | Below 1 V |
| Front washer switch is OFF | 10 to 14 V | |||
| +1 (E66-2) - Body ground | B - Body ground | Front wiper motor LO speed signal circuit | Front wiper motor is in LO operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V | |||
| +SM (E66-10) - Body ground | G- Body ground | Front wiper motor operation signal | Front wiper motor is in LO or HI operation | 10 to 14 V |
| Front wiper motor is OFF | Below 1 V |
| CHECK HEADLIGHT CLEANER CONTROL RELAY |

Disconnect the A44 relay connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| IG (A44-3) - Body ground | L - Body ground | IG signal circuit | Ignition switch on (IG) | 10 to 14 V |
| Ignition switch off | Below 1 V | |||
| E (A44-4) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the A44 relay connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| HDLO (A44-1) - Body ground | BR - Body ground | Headlight LO signal | Headlight control switch LO | 10 to 14 V |
| Headlight control switch except LO | Below 1 V | |||
| H (A44-2) - Body ground | R - Body ground | Headlight cleaner switch signal | Headlight cleaner switch ON, headlight control switch LO | 10 to 14 V |
| Headlight cleaner switch ON, headlight control switch except LO | Below 1 V | |||
| PB (A44-6) - Body ground | B - Body ground | Headlight cleaner motor signal | Headlight cleaner switch ON, headlight control switch except LO | 10 to 14 V |
| Headlight cleaner switch ON, headlight control switch LO | Below 1 V |