Home › ENGINE ยท 2AD-FHV › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REPLACE INTAKE VALVE GUIDE BUSH


    A111299
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on a wooden block.



    A111300E01
  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-10000  
    09950-70010  



    A059172E01
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.
    If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).
    If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head.

  1. Select a new guide bush (STD or O/S 0.05).

    Guide Bush:
    Bush Size
    Specified Condition
    Use STD
    10.985 to 11.006 mm (0.432 to 0.433 in.)
    Use O/S 0.05
    11.035 to 11.056 mm (0.434 to 0.435 in.)



    A111299
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on a wooden block.



    A111371E02
  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000  
    09950-70010  

    Standard protrusion height (H):
    9.0 to 9.4 mm (0.354 to 0.370 in.)



    A100945E02
  1. Using a sharp 6.0 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.
    Text in Illustration 
    *1
    Sharp 6.0 mm Reamer



2. REPLACE EXHAUST VALVE GUIDE BUSH


    A111299
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on a wooden block.



    A111372E01
  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-10000  
    09950-70010  



    A059172E01
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.
    If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).
    If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head.

  1. Select a new guide bush (STD or O/S 0.05).

    Guide Bush:
    Bush Size
    Specified Condition
    Use STD
    10.985 to 11.006 mm (0.432 to 0.433 in.)
    Use O/S 0.05
    11.035 to 11.056 mm (0.434 to 0.435 in.)



    A111299
  1. Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on a wooden block.



    A111373E01
  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000  
    09950-70010  

    Standard protrusion height (H):
    9.0 to 9.4 mm (0.354 to 0.370 in.)



    A100945E02
  1. Using a sharp 6.0 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.
    Text in Illustration 
    *1
    Sharp 6.0 mm Reamer



3. REPLACE CYLINDER HEAD RING PIN

HINT:
It is not necessary to remove the ring pin unless it is being replaced.

  1. Remove the ring pin.



  1. Using a plastic-faced hammer, tap in a new ring pin until the pin stops.


    A203744E01

    Standard Protrusion:
    Item
    Specified Condition
    Pin A
    3.9 to 5.5 mm (0.154 to 0.217 in.)
    Pin B
    2.5 to 3.5 mm (0.0984 to 0.138 in.)



4. REPLACE NO. 1 STRAIGHT SCREW PLUG WITH HEAD


    A203795
  1. Using a 6 mm hexagon wrench, remove the straight screw plugs.

  1. Apply adhesive to new straight screw plugs.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 6 mm hexagon wrench, install the straight screw plugs.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



5. REPLACE CYLINDER HEAD STUD BOLT

HINT:
If a stud bolt is deformed or the threads are damaged, replace it.

  1. Remove the stud bolts.



  1. Using an E8 "TORX" socket wrench, install new stud bolts.

    Torque:
    for stud bolt A and B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    for stud bolt C:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
    for stud bolt D:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A203746E01