CYLINDER HEAD > REPLACEMENT |
| 1. REPLACE INTAKE VALVE GUIDE BUSH |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on a wooden block.
![]() |
Using SST and a hammer, tap out the valve guide bush.
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).
If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush Size | Specified Condition |
| Use STD | 10.985 to 11.006 mm (0.432 to 0.433 in.) |
| Use O/S 0.05 | 11.035 to 11.056 mm (0.434 to 0.435 in.) |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on a wooden block.
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 6.0 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.
| *1 | Sharp 6.0 mm Reamer |
| 2. REPLACE EXHAUST VALVE GUIDE BUSH |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on a wooden block.
![]() |
Using SST and a hammer, tap out the valve guide bush.
![]() |
Using a caliper gauge, measure the bush bore diameter of the cylinder head.
If the bush bore diameter of the cylinder head is more than 11.006 mm (0.433 in.), machine the bush bore diameter to between 11.035 and 11.056 mm (0.434 and 0.435 in.).
If the bush bore diameter of the cylinder head is more than 11.056 mm (0.435 in.), replace the cylinder head.
Select a new guide bush (STD or O/S 0.05).
| Bush Size | Specified Condition |
| Use STD | 10.985 to 11.006 mm (0.432 to 0.433 in.) |
| Use O/S 0.05 | 11.035 to 11.056 mm (0.434 to 0.435 in.) |
![]() |
Gradually heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on a wooden block.
![]() |
Using SST and a hammer, tap in a new guide bush to the specified protrusion height.
![]() |
Using a sharp 6.0 mm reamer, ream the valve guide bush to obtain the standard specified clearance between the valve guide bush and valve stem.
| *1 | Sharp 6.0 mm Reamer |
| 3. REPLACE CYLINDER HEAD RING PIN |
Remove the ring pin.
Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

| Item | Specified Condition |
| Pin A | 3.9 to 5.5 mm (0.154 to 0.217 in.) |
| Pin B | 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
| 4. REPLACE NO. 1 STRAIGHT SCREW PLUG WITH HEAD |
![]() |
Using a 6 mm hexagon wrench, remove the straight screw plugs.
Apply adhesive to new straight screw plugs.
Using a 6 mm hexagon wrench, install the straight screw plugs.
| 5. REPLACE CYLINDER HEAD STUD BOLT |
Remove the stud bolts.
Using an E8 "TORX" socket wrench, install new stud bolts.
