CYLINDER HEAD > INSPECTION |
| 1. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head and cylinder block, and manifolds.
| Item | Specified Condition |
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Exhaust manifold side | |
| Intake manifold side |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If there are cracks, replace the cylinder head sub-assembly.
| 2. INSPECT INNER COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 3. INSPECT INTAKE VALVE |
![]() |
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
![]() |
Using a vernier caliper, measure the overall length of the valve.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| 4. INSPECT EXHAUST VALVE |
![]() |
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
![]() |
Using a vernier caliper, measure the overall length of the valve.
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| 5. INSPECT VALVE GUIDE BUSH |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.035 to 0.070 mm (0.00138 to 0.00276 in.) |
| Item | Specified Condition |
| Intake | 0.06 mm (0.00236 in.) |
| Exhaust | 0.07 mm (0.00276 in.) |
| 6. INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using the following procedure.
Check that Prussian blue appears around the entire valve face and that the valve face is concentric. If not, replace the valve.
Check that Prussian blue appears around the entire valve seat and that the guide and valve face are concentric. If not, resurface the valve seat.
![]() |
Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).
| 7. INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using the following procedure.
Check that Prussian blue appears around the entire valve face and that the valve face is concentric. If not, replace the valve.
Check that Prussian blue appears around the entire valve seat and that the guide and valve face are concentric. If not, resurface the valve seat.
![]() |
Check that the valve seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).
| 8. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the bearing caps and camshaft journals.
Place the camshafts on the cylinder head.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps .
Remove the bearing caps .
![]() |
Measure the Plastigage at its widest point.
Completely remove the Plastigage.