POWER DOOR LOCK CONTROL SYSTEM > Double Lock Function does not Operate Properly |


| 1.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Body / Main body / DTC.
Read DTCs.
| Display (DTC output) | Proceed to |
| DTC is not output | A |
| DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK DOOR LOCK OPERATION |
| Result | Proceed to |
| The double lock function of the driver side front door does not operate properly. | A |
| The double lock function of the passenger side front door does not operate properly. | B |
| The double lock function of the rear RH door does not operate properly. | C |
| The double lock function of the rear LH door does not operate properly. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH |
![]() |
Check the operation of the double lock motor.
Apply the battery voltage to the door lock and set the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) | Lock |
| Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) | Unlock |
Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) | Set |
| Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) | Unset |
While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
Measure the resistance of the double lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 9 (DLSR) - 10 (E) | Set | Below 1 Ω |
| 9 (DLSR) - 10 (E) | Unset | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (DOUBLE DOOR LOCK ECU - DOOR LOCK) |
![]() |
Disconnect the E82 double door lock ECU connector.
Disconnect the G5 door lock connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E82-3 (ACTS) - G5-4 (DL) | Below 1 Ω |
| E82-4 (ATCR) - G5-3 (UNDL) | Below 1 Ω |
| E82-5 (DLPD) - G5-9 (DLSR) | Below 1 Ω |
| G5-10 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH |
![]() |
Check the operation of the double door lock motor.
Apply the battery voltage to the door lock and set the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) | Lock |
| Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) | Unlock |
Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) | Set |
| Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) | Unset |
While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
Measure the resistance of the double lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (E) - 6 (DLSR) | Set | Below 1 Ω |
| 5 (E) - 6 (DLSR) | Unset | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (DOUBLE DOOR LOCK ECU - DOOR LOCK) |
![]() |
Disconnect the E82 double door lock ECU connector.
Disconnect the H5 door lock connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E82-3 (ACTS) - H5-2 (DL) | Below 1 Ω |
| E82-4 (ATCR) - H5-1 (UNDL) | Below 1 Ω |
| E82-6 (DLPP) - H5-6 (DLSR) | Below 1 Ω |
| H5-5 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.INSPECT REAR DOOR WITH MOTOR LOCK ASSEMBLY LH |
![]() |
Check the operation of the double door lock motor.
Apply the battery voltage to the door lock and set the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) | Lock |
| Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) | Unlock |
Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) | Set |
| Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) | Unset |
While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
Measure the resistance of the double lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 9 (DLSR) - 10 (E) | Set | Below 1 Ω |
| 9 (DLSR) - 10 (E) | Unset | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK WIRE HARNESS (DOUBLE DOOR LOCK ECU - DOOR LOCK) |
![]() |
Disconnect the E82 double door lock ECU connector.
Disconnect the J4 door lock connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E82-3 (ACTS) - J4-4 (DL) | Below 1 Ω |
| E82-4 (ATCR) - J4-3 (UNDL) | Below 1 Ω |
| E82-6 (DLPP) - J4-9 (DLSR) | Below 1 Ω |
| J4-10 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 9.INSPECT REAR DOOR WITH LOCK ASSEMBLY RH |
![]() |
Check the operation of the double door lock motor.
Apply the battery voltage to the door lock and set the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) | Lock |
| Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) | Unlock |
Apply the battery voltage to the door lock motor and check the operation of the double door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) | Set |
| Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) | Unset |
While the double locking system is set, check that the doors cannot be unlocked by operating the control cable.
Measure the resistance of the double lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (DLSR) - 6 (E) | Set | Below 1 Ω |
| 5 (DLSR) - 6 (E) | Unset | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK WIRE HARNESS (DOUBLE DOOR LOCK ECU - REAR DOOR LOCK RH) |
![]() |
Disconnect the E82 double door lock ECU connector.
Disconnect the I4 door lock connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E82-3 (ACTS) - I4-2 (DL) | Below 1 Ω |
| E82-4 (ATCR) - I4-1 (UNDL) | Below 1 Ω |
| E82-11 (DLPR) - I4-5 (DLSR) | Below 1 Ω |
| I4-6 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||