Home › DRIVE LINE › GF1A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT


C126625
  1. Remove the 4 stud bolts.



2. REMOVE TRANSFER CASE STRAIGHT PIN


C127246E01
  1. Remove the 2 straight pins.



3. REMOVE TRANSFER CASE NO. 1 PLUG
  1. Remove the No. 1 plug.

  1. Remove the gasket from the No. 1 plug.



4. REMOVE TRANSFER CASE NO. 2 PLUG


C126626E01
  1. Remove the No. 2 plug.

  1. Remove the gasket from the No. 2 plug.



5. REMOVE TRANSFER DRAIN PLUG


C126627E01
  1. Remove the drain plug.

  1. Remove the gasket from the drain plug.



6. REMOVE TRANSFER CASE OIL SEAL LH


C126628E01
  1. Using SST, tap out the oil seal from the case.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil seal lip.



7. REMOVE TRANSFER CASE OIL SEAL RH


C126629
  1. Using SST, tap out the oil seal from the case.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil seal lip.



8. INSPECT RING GEAR BACKLASH


C126630E01
  1. Using a dial indicator, measure the backlash of the ring gear at 3 points.

    Standard backlash:
    0.10 to 0.20 mm (0.0039 to 0.0079 in.)

    If the backlash is not within the specified range, adjust the backlash or repair as necessary.



9. REMOVE NO. 1 TRANSFER CASE COVER


    C126631
  1. Remove the 8 bolts.



    C126632
  1. Using a brass bar and hammer, tap out the cover from the case.



10. REMOVE TRANSFER RING GEAR


C126633
  1. Remove the ring gear from the transfer case.



11. REMOVE TRANSFER CASE STRAIGHT PIN
  1. Remove the 2 straight pins from the transfer case.



12. REMOVE TRANSFER OUTPUT REAR SHAFT SUB-ASSEMBLY


C126635
  1. Remove the 5 bolts and transfer output rear shaft.



    C109626E01
  1. Using SST and a hammer, unstake the lock nut.

    SST
    09930-00010  

  1. Remove the lock nut.



13. REMOVE TRANSFER DRIVEN PINION


C109627E01
  1. Using SST and a press, press out the driven pinion from the output shaft.

    SST
    09950-00020  
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)



14. REMOVE TRANSFER OUTPUT REAR SHAFT DUST DEFLECTOR


    C109629E01
  1. Using SST and a press, press out the dust deflector from the output rear shaft.

    SST
    09950-00020  



15. REMOVE TRANSFER DRIVEN PINION FRONT BEARING


C109628E02
  1. Using SST and a press, press out the driven pinion from the bearing.

    SST
    09950-00020  
    09950-60010   (09951-00420)
    09950-70010   (09951-07100)



    C109630
  1. Remove the O-ring from the bearing.



16. REMOVE TRANSFER OUTPUT SHAFT WASHER


C110759
  1. Remove the washer from the transfer pinion gear.



17. REMOVE RING GEAR MOUNTING CASE BEARING (for LH side)


C109631E01
  1. Using SST, remove the bearing from the mounting case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00540)



    C109633E01
  1. Using SST and a hammer, tap out the bearing.

    SST
    09310-35010  



18. REMOVE RING GEAR MOUNTING CASE WASHER


19. REMOVE RING GEAR MOUNTING CASE BEARING (for RH side)


C109632
  1. Using SST, remove the bearing from the mounting case.

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00540)

  1. Using SST and a hammer, tap out the bearing (race) from the cover.

    SST
    09636-20010  



20. REMOVE TRANSFER RING GEAR MOUNTING CASE NO. 2 WASHER


21. REMOVE SHAFT SNAP RING


C109636
  1. Using a snap ring expander, remove the snap ring.



22. REMOVE TRANSFER RING GEAR MOUNTING CASE


C109637E01
  1. Using SST and a press, press out the ring gear from the mounting case.

    SST
    09950-60010   (09951-00400)



23. REMOVE BREATHER OIL DEFLECTOR


C109640
  1. Remove the 2 bolts and oil deflector.



24. REMOVE TRANSFER CASE BREATHER PLUG


C109638
  1. Remove the breather plug from the transfer case.