POWER DOOR LOCK CONTROL SYSTEM > Only Passenger Door LOCK / UNLOCK Functions do not Operate |

| 1.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY (PASSENGER SIDE) |
![]() |
for LHD:
Apply the battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) | Lock |
| Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) | Unlock |
Measure the resistance of the door lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 7 (E) - 8 (LSSR) | Lock | 10 kΩ or higher |
| 7 (E) - 8 (LSSR) | Unlock | Below 1 Ω |
![]() |
for RHD (w/o Double Locking System):
Apply the battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) | Lock |
| Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) | Unlock |
Measure the resistance of the door lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 7 (LSSR) - 8 (E) | Lock | 10 kΩ or higher |
| 7 (LSSR) - 8 (E) | Unlock | Below 1 Ω |
![]() |
for RHD (w/ Double Locking System):
Apply the battery voltage to the door lock motor and check the operation of the door lock motor.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) | Lock |
| Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) | Unlock |
Measure the resistance of the door lock position switch.
| Tester Connection | Switch Condition | Specified Condition |
| 7 (E) - 8 (LSSR) | Lock | 10 kΩ or higher |
| 7 (E) - 8 (LSSR) | Unlock | Below 1 Ω |
|
| ||||
| OK | |
| 2.CHECK WIRE HARNESS (DOOR LOCK - ECU) |

for LHD:
Disconnect the G5 door lock connector.
Disconnect the E18 ECU connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| G5-1 (UL) - IH-18 (ACT-) | Below 1 Ω |
| G5-4 (L) - IH-17 (ACT+) | Below 1 Ω |
| G5-7 (LSSR) - E18-10 (LSWP) | Below 1 Ω |
| G5-8 (E) - Body ground | Below 1 Ω |
for RHD (w/o Double Locking System):
Disconnect the H5 door lock connector.
Disconnect the E18 ECU connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H5-1 (UL) - IH-9 (ACT-) | Below 1 Ω |
| H5-4 (L) - IH-8 (ACT+) | Below 1 Ω |
| H5-8 (LSSR) - E18-10 (LSWP) | Below 1 Ω |
| H5-7 (E) - Body ground | Below 1 Ω |
for RHD (w/ Double Locking System):
Disconnect the H5 door lock connector.
Disconnect the E18 ECU connector.
Disconnect the IH junction block connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H5-3 (UL) - IH-9 (ACT-) | Below 1 Ω |
| H5-4 (L) - IH-8 (ACT+) | Below 1 Ω |
| H5-8 (LSSR) - E18-10 (LSWP) | Below 1 Ω |
| H5-7 (E) - Body ground | Below 1 Ω |
|
| ||||
| OK | ||
| ||