CAN COMMUNICATION SYSTEM > Open in One Side of CAN Branch Line |
| Symptom | Trouble Area |
| 2 or more ECUs and/or sensors do not appear on intelligent tester "Bus Check" screen. |
|




| 1.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (BRAKE ACTUATOR) |
Disconnect the A27 brake actuator (skid control ECU) connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "ABS/VSC/TRC" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "ABS/VSC/TRC" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 2.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (BRAKE ACTUATOR BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A27-6 (CANH) - A27-5 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 3.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (ABS AND TRACTION ACTUATOR) |
Disconnect the A67 ABS and traction actuator (skid control ECU) connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "ABS/VSC/TRC" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "ABS/VSC/TRC" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 4.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (ABS AND TRACTION ACTUATOR BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-25 (CANH) - A67-14 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 5.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR) |
Disconnect the K25 yaw rate sensor connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "Yaw Rate / Deceleration Sensor" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "Yaw Rate / Deceleration Sensor" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 6.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (YAW RATE SENSOR BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K25-3 (CANH) - K25-2 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (STEERING ANGLE SENSOR) |
Disconnect the E95 steering angle sensor connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "Steering Angle Sensor" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "Steering Angle Sensor" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 8.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (STEERING ANGLE SENSOR BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E95-3 (CANH) - E95-2 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (POWER STEERING ECU) |
Disconnect the E21 power steering ECU connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "EPS" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "EPS" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 10.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (POWER STEERING ECU BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E21-2 (CANH) - E21-8 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 11.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU) |
Disconnect the E20 main body ECU connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "Main Body" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "Main Body" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 12.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (MAIN BODY ECU BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E20-15 (CANH) - E20-16 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER) |
Disconnect the E41*1 or E42*2 air conditioning amplifier connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "Air Conditioner" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "Air Conditioner" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 14.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (AIR CONDITIONING AMPLIFIER BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E41-11 (CANH) - E41-12 (CANL)*1 | Ignition switch off | 54 to 64 Ω |
| E42-8 (CANH) - E42-9 (CANL)*2 | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 15.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (4WD CONTROL ECU) |
Disconnect the E67 4WD control ECU connector.
Select "Bus Check" on the intelligent tester display (Click here).
| Result | Proceed to |
| "Four Wheel Drive Control" not displayed on intelligent tester. | A |
| Several ECUs and sensors in addition to "Four Wheel Drive Control" not displayed on intelligent tester. | B |
|
| ||||
| A | |
| 16.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (4WD CONTROL ECU BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E67-14 (CANH) - E67-16 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||
| 17.CHECK FOR OPEN IN ONE SIDE OF BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY BRANCH WIRE) |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.
![]() |
Disconnect the E49 center airbag sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E49-13 (CANH) - E49-22 (CANL) | Ignition switch off | 54 to 64 Ω |
|
| ||||
| OK | ||
| ||