Home › DRIVE LINE › DIFFERENTIAL › ACTIVE TORQUE CONTROL 4WD SYSTEM

DTC    C1241/94    Low Power Supply Voltage

for Preparation Click here


DESCRIPTION

If a malfunction in the power source circuit occurs, or a malfunction in communication with the skid control ECU or in a speed sensor occurs, the 4WD control ECU will prohibit operations by the fail-safe function.

DTC No.
DTC Detection Condition
Trouble Area
C1241/94
When one of following conditions is met:
  1. When following continues for 10 seconds or more:
    - At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less.
  2. When both of following continue for 60 seconds or more:
    - With the voltage of IG1 terminal 9.5 V or less, communication with the skid control ECU cannot be performed.
    - A Malfunction in communication with skid control ECU.
  3. When following continue for 3 seconds or more:
    - With the voltage of IG1 terminal 17 V or more, communication with the skid control ECU cannot be performed.
  1. Battery
  1. Generator
  1. ECU-IG1
  1. Wire harness (IG1 circuit, GND circuit)
  1. 4WD control ECU

WIRING DIAGRAM


C204187E01


INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).

1.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch on (IG) and check that no CAN communication system DTC is output.

  1. Start the engine.

  1. Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more, and check that no speed sensor DTC (brake control system DTC) is output (Click here and Click here).

    Result:

    Result
    Proceed to
    Neither CAN communication system DTC nor speed sensor DTC (Brake control system DTC) is output
    A
    CAN communication system DTC is output
    B
    Speed sensor DTC (Brake control system DTC) is output
    C

    HINT:
    When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



B
REPAIR CIRCUIT INDICATOR BY OUTPUT CODE (CAN COMMUNICATION SYSTEM)

C
REPAIR CIRCUIT INDICATOR BY OUTPUT CODE (BRAKE CONTROL SYSTEM)
A


2.INSPECT FUSE (ECU-IG1)
  1. Remove the ECU-IG1 fuse from the instrument junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1Ω

    HINT:
    Check for short circuits in all harnesses and connector connected to the ECU-IG1 fuse (Click here).



NG
REPLACE FUSE
OK


3.CHECK WIRE HARNESS (4WD CONTROL ECU - BATTERY)
C107387E07
  1. Disconnect the E67 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E67-11 (IG1) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.CHECK WIRE HARNESS (4WD CONTROL ECU - BODY GROUND)
C107387E08
  1. Disconnect the E67 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E67-23 (GND) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more, and check if the same DTC is output.

    Result:
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B

    HINT:
    Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.



B
END
A

REPLACE 4WD CONTROL ECU