Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Light Control Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the headlight dimmer switch.

WIRING DIAGRAM


B128021E01


INSPECTION PROCEDURE

1.CHECK VEHICLE CONDITION
  1. Check the vehicle condition.
    Result 
    Result
    Proceed to
    w/o Automatic light control system
    A
    w/ Automatic light control system
    B

    HINT:
    There are no settings in the Data List related to the AUTO position, so proceed to "A" for all switch positions other than AUTO.



B
Go to step 3
A


2.READ VALUE USING INTELLIGENT TESTER (MAIN BODY ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and press the intelligent tester main switch ON.

  1. Select the items below in the Data List, and read the displays on the intelligent tester.

    Main body ECU 
    Item
    Measurement / Display (Range)
    Normal Condition
    Diagnostic Note
    Dimmer SW
    Headlight dimmer switch signal / ON or OFF
    ON: Headlight dimmer switch is in HI or FLASH position
    OFF: Headlight dimmer switch is in LO position
    -
    Passing Light SW
    Passing light switch signal / ON or OFF
    ON: Headlight dimmer switch is in FLASH position
    OFF: Headlight dimmer switch is in except FLASH position
    -
    Front Fog Light SW
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch is in ON position
    OFF: Front fog light switch is in OFF position
    -
    Rear Fog Light SW
    Rear fog light switch signal / ON or OFF
    ON: Rear fog light switch is in ON position
    OFF: Rear fog light switch is in OFF position
    -
    Head Light SW (Head)
    Headlight control switch signal (HEAD) / ON or OFF
    ON: Light control switch is in HEAD position
    OFF: Light control switch is in except HEAD position
    -
    Head Light SW (Tail)
    Headlight control switch signal (TAIL) / ON or OFF
    ON: Light control switch is in TAIL or HEAD position
    OFF: Light control switch is in except OFF position
    -

    OK:
    ON or OFF is displayed on the intelligent tester screen according to the switch condition.



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


3.INSPECT HEADLIGHT DIMMER SWITCH

B128074E01

  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    for LH side 
    Tester Connection
    Condition
    Specified Condition
    18 (T) - 12 (EL)
    Light control switch TAIL
    Below 1 Ω
    20 (H) - 12 (EL)
    Light control switch HEAD
    Below 1 Ω
    19 (A) - 12 (EL)
    Light control switch AUTO
    Below 1 Ω
    16 (HL) - 12 (EL)
    Dimmer switch LOW
    Below 1 Ω
    11 (HU) - 12 (EL)
    Dimmer switch HIGH
    Below 1 Ω
    17 (HF) - 12 (EL)
    Dimmer switch FLASH
    Below 1 Ω
    4 (BFG) - 3 (LFG)
    Fog light switch ON
    Below 1 Ω
    2 (B) - 3 (LFG)
    Rear fog light switch ON
    Below 1 Ω
    for RH side 
    Tester Connection
    Condition
    Specified Condition
    13 (T) - 19 (EL)
    Light control switch TAIL
    Below 1 Ω
    11 (H) - 19 (EL)
    Light control switch HEAD
    Below 1 Ω
    15 (HL) - 19 (EL)
    Dimmer switch LOW
    Below 1 Ω
    20 (HU) - 19 (EL)
    Dimmer switch HIGH
    Below 1 Ω
    14 (HF) - 19 (EL)
    Dimmer switch FLASH
    Below 1 Ω
    7 (BFG) - 8 (LFG)
    Fog light switch ON
    Below 1 Ω
    9 (B) - 8 (LFG)
    Rear fog light switch ON
    Below 1 Ω



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK


4.CHECK WIRE HARNESS (MAIN BODY ECU - DIMMER SWITCH AND BODY GROUND)

B128024E01

  1. Disconnect the E18 and E20 main body ECU connectors.

  1. Disconnect the IJ instrument panel junction block connector.

  1. Disconnect the E15 headlight dimmer switch connector.

  1. Measure the resistance wire harness side connector.

    Standard resistance:
    for LH Side 
    Tester Connection
    Specified Condition
    E15-17 (HF) - E18-22 (HF)
    Below 1 Ω
    E15-17 (HF) or E18-22 (HF) - Body ground
    10 kΩ or higher
    E15-20 (H) - E20-12 (HEAD)
    Below 1 Ω
    E15-20 (H) or E20-12 (HEAD) - Body ground
    10 kΩ or higher
    E15-19 (A) - E20-18 (A)
    Below 1 Ω
    E15-19 (A) or E20-18 (A) - Body ground
    10 kΩ or higher
    E15-4 (BFG) - E20-13 (FFOG)
    Below 1 Ω
    E15-4 (BFG) or E20-13 (FFOG) - Body ground
    10 k Ω or higher
    E15-2 (B) - E20-9 (RFOG)
    Below 1 Ω
    E15-2 (B) or E20-9 (RFOG) - Body ground
    10 kΩ or higher
    E15-18 (T) - E18-21 (TAIL)
    Below 1 Ω
    E15-18 (T) or E18-21 (TAIL) - Body ground
    10 kΩ or higher
    E15-11 (HU) - IJ-4 (HU)
    Below 1 Ω
    E15-11 (HU) or IJ-4 (HU) - Body ground
    10 kΩ or higher
    E15-12 (EL) - Body ground
    Below 1 Ω
    E15-3 (LFG) - Body ground
    Below 1 Ω
    for RH side 
    Tester Connection
    Specified Condition
    E15-14 (HF) - E18-22 (HF)
    Below 1 Ω
    E15-14 (HF) or E18-22 (HF) - Body ground
    10 kΩ or higher
    E15-11 (H) - E20-12 (HEAD)
    Below 1 Ω
    E15-11 (H) or E20-12 (HEAD) - Body ground
    10 kΩ or higher
    E15-7 (BFG) - E20-13 (FFOG)
    Below 1 Ω
    E15-7 (BFG) or E20-13 (FFOG) - Body ground
    10 kΩ or higher
    E15-9 (B) - E20-9 (RFOG)
    Below 1 Ω
    E15-9 (B) or E20-9 (RFOG) - Body ground
    10 kΩ or higher
    E15-13 (T) - E18-21 (TAIL)
    Below 1 Ω
    E15-13 (T) or E18-21 (TAIL) - Body ground
    10 kΩ or higher
    E15-20 (HU) - IJ-4 (HU)
    Below 1 Ω
    E15-20 (HU) or IJ-4 (HU) - Body ground
    10 kΩ or higher
    E15-19 (EL) - Body ground
    Below 1 Ω
    E15-8 (LFG) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)