Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

DTC    B2326    CAN MS Bus Line Communication Malfunction

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
B2326
Lost Communication with the main body ECU.
  1. CAN No. 2 bus circuit
  2. Certification ECU branch wire or connector
  3. Main body ECU main wire or connector
  4. Combination meter ECU main wire or connector
  5. Main body ECU
  6. Combination meter ECU
  7. Certification ECU
  8. No. 4 junction connector

HINT:
For vehicles with entry and start system only.


WIRING DIAGRAM


C191511E02


C191511E03


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the main wire and the branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  3. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.CHECK CAN BUS LINE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)

C129289E04

  1. Remove the main body ECU with the connector connected.

  1. Disconnect the IB and IE main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    54 to 69 Ω
    Below 54 Ω: Short in line
    Higher than 69 Ω : Open in CAN main bus line
    E19-11 (CANP) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E19-12 (CANN) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E19-11 (CANP) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E19-12 (CANN) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main bus line
    A
    NG
    - Short in line
    - +B short
    - Ground short
    B
    OK
    C



B
Go to step 5

C
Go to step 10
A


2.CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 4 JUNCTION CONNECTOR)

F100894E42

  1. Disconnect the E76 junction connector (No. 4 junction connector).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Inspection Area
    E76-9 (MSCH) - E76-20 (MSCL)
    Ignition switch off
    108 to 132 Ω
    Combination meter side CAN main wire
    E76-11 (CANP) - E76- 22 (CANN)
    Ignition switch off
    108 to 132 Ω
    Main body ECU side CAN main wire

    Result 
    Result
    Proceed to
    NG (Combination meter side CAN main wire)
    A
    NG (Main body ECU side CAN main wire)
    B
    OK
    C



B
Go to step 4

C
REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR
A


3.CHECK CAN MAIN WIRE FOR DISCONNECTION (COMBINATION METER ECU)

C129295E02

  1. Disconnect the E76 junction connector (No. 4 junction connector).

  1. Remove the combination meter ECU with the connector connected.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-9 (MSCH) - E22-10 (MSCL)
    Ignition switch off
    108 to 132 Ω



NG
REPLACE COMBINATION METER ECU
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR 

4.CHECK CAN MAIN WIRE FOR DISCONNECTION (MAIN BODY ECU)

C129290E01

  1. Disconnect the E76 junction connector.

  1. Remove the main body ECU with the connector connected.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    108 to 132 Ω



G
REPLACE MAIN BODY ECU
OK

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR 

5.CHECK CAN BUS LINE FOR SHORT

C129289E04

  1. Remove the main body ECU with the connector connected.

  1. Disconnect the IB and IE main body ECU connectors.

  1. Disconnect the E22 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-12 (CANN) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-11 (CANP) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-12 (CANN) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    108 to 132 Ω

  1. Disconnect the E63 certification ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-12 (CANN) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-11 (CANP) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-12 (CANN) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (Combination meter ECU)
    B
    OK (Certification ECU)
    C



B
REPLACE COMBINATION METER ECU

C
REPLACE CERTIFICATION ECU
A


6.CHECK CAN BUS LINE FOR SHORT

C129289E04

  1. Remove the main body ECU with the connector connected.

  1. Disconnect the IE and IB main body ECU connectors.

  1. Disconnect the E76 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-12 (CANN) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-11 (CANP) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-12 (CANN) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    108 to 132 Ω



OK
Go to step 8
NG


7.CHECK CAN BUS LINE FOR SHORT

C129296E03

  1. Disconnect the E19 ECU connector.

  1. Disconnect the IB and IE main body ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-12 (CANN) - IB-30 (BECU)
    Ignition switch off
    6 kΩ or higher
    E19-11 (CANP) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-12 (CANN) - IE-17 (GND1)
    Ignition switch off
    200 Ω or higher
    E19-11 (CANP) - E19-12 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.CHECK CAN BUS LINE FOR SHORT

C129294E02

  1. Disconnect the E76 junction connector.

  1. Disconnect the E22 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-9 (CANP) - E22-10 (CANN)
    Ignition switch off
    108 to 132 Ω
    E22-9 (CANP) - E22-22 (B)
    Ignition switch off
    6 kΩ or higher
    E22-10 (CANN) - E22-22 (B)
    Ignition switch off
    6 kΩ or higher
    E22-9 (CANP) - E22-33 (ET)
    Ignition switch off
    200 Ω or higher
    E22-10 (CANN) - E22-33 (ET)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    OK
    w/ Entry and start system
    A
    OK
    w/o Entry and start system
    B
    NG
    C



B
REPLACE COMBINATION METER ECU

C
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR
A


9.CHECK CAN BUS LINE FOR SHORT

C129293E01

  1. Disconnect the E76 junction connector.

  1. Disconnect the E63 certification ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E63-27 (CANH) - E63-28 (CANL)
    Ignition switch off
    54 to 69 Ω
    E63-27 (CANH) - E63-1 (+B1)
    Ignition switch off
    6 kΩ or higher
    E63-28 (CANL) - E63-1 (+B1)
    Ignition switch off
    6 kΩ or higher
    E63-27 (CANH) - E63-17 (E)
    Ignition switch off
    200 Ω or higher
    E63-28 (CANL) - E63-17 (E)
    Ignition switch off
    200 Ω or higher



NG
REPLACE CERTIFICATION ECU OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE CERTIFICATION ECU 

10.CHECK CAN BUS LINE FOR DISCONNECTION
  1. Recheck for DTC.


NEXT

Go to DTC CHART