Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Door LOCK Position Circuit

for Preparation Click here


DESCRIPTION

This circuit detects the state of the door lock detection sensor and sends it to the main body ECU.

WIRING DIAGRAM


B128036E01


B128035E03


INSPECTION PROCEDURE

1.INSPECT DOOR LOCK


  1. for LHD:


    B128037E03

    1. Remove the front driver side door lock.

    2. Remove the front passenger side door lock*.

    3. Remove the back door lock*.

      HINT:
      *: w/ Entry and start system

    4. Measure the resistance of the door lock.

      Standard resistance:
      Front driver side door lock 
      Tester connection
      Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Front passenger side door lock* 
      Tester connection
      Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Back door lock* 
      Tester connection
      Condition
      Specified Condition
      7 (S) - 8 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher

      HINT:
      *: w/ Entry and start system



  1. for RHD:


    B128038E01

    1. Remove the front driver side door lock.

    2. Remove the front passenger side door lock*.

    3. Remove the rear door lock LH and RH*.

    4. Remove the back door lock*.

      HINT:
      *: w/ Entry and start system or w/ Double locking system

    5. Measure the resistance of the door lock.

      Standard resistance:
      Front driver side door lock 
      Tester connection
      Condition
      Specified Condition
      7 (LSSR) - 8 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Front passenger side door lock* 
      Tester connection
      Condition
      Specified Condition
      8 (LSSR) - 7 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Rear door lock LH* 
      Tester connection
      Condition
      Specified Condition
      5 (LSSR) - 6 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Rear door lock RH* 
      Tester connection
      Condition
      Specified Condition
      9 (LSSR) - 10 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher
      Back door lock* 
      Tester connection
      Condition
      Specified Condition
      7 (S) - 8 (E)
      LOCK
      Below 1 Ω
      UNLOCK
      10 kΩ or higher

      HINT:
      *: w/ Entry and start system or w/ Double locking system



NG
REPLACE DOOR LOCK ASSEMBLY
OK


2.CHECK WIRE HARNESS (MAIN BODY ECU - POSITION SWITCH AND BODY GROUND)


    B128039E01
  1. for LHD:

    1. Install the door lock.

    2. Connect the door lock connectors.

    3. Disconnect the E18 main body ECU connector.

    4. Measure the resistance of the wire harness side connector.

      Standard resistance:
      w/o Entry and start system 
      Tester connection
      Condition
      Specified Condition
      E18-25 (LSWD) - Body ground
      Driver side door LOCK
      Below 1 Ω
      Driver side door UNLOCK
      10 kΩ or higher
      w/ Entry and start system 
      Tester connection
      Condition
      Specified Condition
      E18-25 (LSWD) - Body ground
      Driver side door LOCK
      Below 1 Ω
      Driver side door UNLOCK
      10 kΩ or higher
      E18-10 (LSWP) - Body ground
      Passenger side door LOCK
      Below 1 Ω
      Passenger side door UNLOCK
      10 kΩ or higher
      E18-13 (LSWB) - Body ground
      Back door LOCK
      Below 1 Ω
      Back door UNLOCK
      10 kΩ or higher



    B128040E01
  1. for RHD:

    1. Install the door lock.

    2. Connect the door lock connectors.

    3. Disconnect the E18 and E20* main body ECU connector.

      HINT:
      *: w/ Entry and start system

    4. Measure the resistance of the wire harness side connectors.


Standard resistance:
w/o Entry and start system 
Tester connection
Condition
Specified Condition
E18-25 (LSWD) - Body ground
Driver side door LOCK
Below 1 Ω
Driver side door UNLOCK
10 kΩ or higher
w/ Entry and start system 
Tester connection
Condition
Specified Condition
E18-25 (LSWD) - Body ground
Driver side door LOCK
Below 1 Ω
Driver side door UNLOCK
10 kΩ or higher
E18-10 (LSWP) - Body ground
Passenger side door LOCK
Below 1 Ω
Passenger side door UNLOCK
10 kΩ or higher
E18-13 (LSWB) - Body ground
Back door LOCK
Below 1 Ω
Back door UNLOCK
10 kΩ or higher
E20-10 (LSR) - Body ground
Rear door LH LOCK
Rear door RH LOCK
Below 1 Ω
Rear door LH UNLOCK
Rear door RH UNLOCK
10 kΩ or higher
w/o Entry and start system and w/ Double locking system 
Tester connection
Condition
Specified Condition
E18-25 (LSWD) - Body ground
Driver side door LOCK
Except passenger side door UNLOCK
Below 1 Ω
Driver side door UNLOCK
10 kΩ or higher
E18-10 (LSWP) - Body ground
Passenger side door LOCK
Except passenger side door UNLOCK
Below 1 Ω
Passenger side door UNLOCK
Except passenger side door UNLOCK
10 kΩ or higher
Back door LOCK
Except back door UNLOCK
Below 1 Ω
Back door UNLOCK
Except back door UNLOCK
10 kΩ or higher
Rear door LH and RH LOCK
Except rear door LH and RH UNLOCK
Below 1 Ω
Rear door LH and RH UNLOCK
Except rear door LH and RH UNLOCK
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)