Home › BODY › ENGINE HOOD / DOOR › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. w/ Navigation System (for HDD):
    After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


B129158
  1. Using a screwdriver, detach the clip, 3 claws and remove the garnish.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT ARMREST BASE UPPER PANEL LH


B129159
  1. Using a screwdriver, detach the clip, 5 claws, and remove the panel (with the switch).

    HINT:
    Tape the screwdriver tip before use.

  1. Disconnect the switch connectors.



    B129161
  1. for Driver Side:
    Remove the 3 screws and power window regulator master switch from the panel.

    NOTICE:
    Be careful when removing the screws as the switch may fall and become damaged.



    B139756
  1. for Passenger Side:
    Using a screwdriver, detach the 2 claws and remove the power window regulator switch from the panel.

    HINT:
    Tape the screwdriver tip before.

    NOTICE:
    Be careful when detaching the claws as the switch may fall and become damaged.



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


B129165
Using a screwdriver, detach the 12 claws and remove the door assist grip.

HINT:
B129164
Tape the screwdriver tip before use.
Using a screwdriver, detach the 3 claws and remove the door inside handle plug.

HINT:
Tape the screwdriver tip before use.



    B129166
  1. Remove the 3 screws.

  1. Using a screwdriver, detach the 10 clips, 2 claws and remove the trim.

    HINT:
    1. Tape the screwdriver tip before use.
    2. If the screwdriver cannot reach the clips, pull on the lower trim to remove it.

  1. Using a screwdriver, detach the 7 claws and remove the weatherstrip inner.

    HINT:
    Tape the screwdriver tip before use.

  1. Using a screwdriver, detach the 4 claws and remove the speaker door grille.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


B129405E01
  1. Disconnect the mirror connector labeled A.

  1. Remove the 3 screws.

  1. Remove the outer rear view mirror.



6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


B131486
  1. Disconnect the connector.

  1. Using a drill bit with a diameter of less than 4 mm (0.157 in.), drill out the 3 rivet heads and remove the speaker.

    NOTICE:
    1. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    2. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



7. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    B131481
  1. Disconnect the connector.

  1. Remove the 2 screws and speaker.



8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


B133476E01
  1. Disconnect the 2 cables from the inside handle and remove the inside handle.



9. REMOVE FRONT DOOR SERVICE HOLE COVER LH


B129167
  1. Disconnect each connector and remove the service hole cover.

    NOTICE:
    Remove the remaining tape on the door.



10. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH


    B130251
  1. Put protective tape under the belt moulding.

  1. Using a moulding remover, detach the claws to remove the belt moulding as shown in the illustration.

    HINT:
    Tape the remover tip before use.

    NOTICE:
    Be careful when removing the belt moulding as there are claws attached to the front and rear ends of the belt moulding.



11. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Driver Side:
    Temporarily install the power window regulator master switch.

  1. for Passenger Side:
    Temporarily install the power window regulator switch.



    B129168
  1. Move the door glass until the 2 bolts appear in the service holes.

  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.



    B129169E01
  1. Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver side:
    Remove the power window regulator master switch.

  1. Passenger side:
    Remove the power window regulator switch.



12. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


B129170
  1. Disconnect the connector.

  1. Remove the 6 bolts and regulator.

    HINT:
    Remove the window regulator through the service hole.

    NOTICE:
    Be careful when removing the bolts as the window regulator may fall and become damaged.



13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


B129173
  1. Using a T25 "torx" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.



14. REMOVE FRONT DOOR LOWER REAR FRAME SUB-ASSEMBLY LH


B129171
  1. Remove the bolt.

    HINT:
    Remove the frame through the service hole.

    NOTICE:
    Be careful when removing the bolts as the frame may fall and become damaged.



15. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)


B129200E01
  1. Remove the hole plug.

  1. Using a T30 "torx" socket, loosen the screw and remove the cover (with door lock cylinder).

    HINT:
    Loosen but do not remove the screw.

  1. Remove the door lock cylinder from the cover.



16. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Front Passenger Side)


B129202E01
  1. Remove the hole plug.

  1. Using a T30 "torx" socket, loosen the screw and remove the cover.

    HINT:
    Loosen but do not remove the screw.



17. REMOVE FRONT DOOR LOCK ASSEMBLY LH


B129199
  1. Disconnect the connector.

  1. Using a T30 "torx" socket, remove the 3 screws.

    NOTICE:
    Be careful when removing the bolts as the door lock may fall and become damaged.



    B065961E07
  1. Slide the door lock downward to disconnect the front door lock open rod from the door lock. Then remove the door lock (with cable).

    HINT:
    Remove the door lock through the service hole.



    B129194
  1. Remove the door lock wiring harness packing from the door lock.



    B129197
  1. Using a screwdriver, detach the 3 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B129195
  1. Remove the 2 cables as shown in the illustration.



18. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
  1. w/ Entry and Start System:
    Disconnect the connector.



    B129365
  1. Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.



19. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B135427
  1. w/ Entry and Start System:
    Disconnect the connector and clamp.



    B129198
  1. Using a T30 "torx" socket, loosen the screw of the frame.



    B057102E01
  1. Using pliers, pinch the clip.

    NOTICE:
    Be sure to remove the outside handle frame together with the clip, as the clip will be damaged if it remains attached to the door panel.



    B129363
  1. Detach the claw and remove the frame.

    HINT:
    Remove the frame through the service hole.

  1. Remove the front door lock open rod.



20. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD


B129193
  1. Detach the 2 claws and remove the pad.



21. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD


B129192
  1. Detach the 2 claws and remove the pad.



22. REMOVE FRONT DOOR CHECK ASSEMBLY LH


B061953E01
  1. Remove the 3 bolts and door check.

    HINT:
    Remove the door check through the service hole.



23. REMOVE FRONT DOOR GLASS RUN LH


24. REMOVE FRONT DOOR WEATHERSTRIP LH


B129186
  1. Using a clip remover, detach the 17 clips and remove the weatherstrip.

    HINT:
    If clips are damaged during removal, replace them.



25. REMOVE CUSHION
  1. Remove the 2 cushions.