FRONT DOOR > REASSEMBLY |
| 1. INSTALL CUSHION |
Install the 2 cushions.
| 2. INSTALL FRONT DOOR WEATHERSTRIP LH |
![]() |
Attach the 17 clips to install the weatherstrip.
| 3. INSTALL FRONT DOOR GLASS RUN LH |
| 4. INSTALL FRONT DOOR CHECK ASSEMBLY LH |
![]() |
Apply MP grease to the sliding areas of the door check.
Install the door check to the door panel with the 2 bolts.
Apply adhesive to the bolt.
Install the door check to the body panel with the bolt.
| 5. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD |
![]() |
Attach the 2 claws to install the pad.
| 6. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD |
![]() |
Attach the 2 claws to install the pad.
| 7. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH |
Install the front door lock open rod.
![]() |
Attach the claw and clip to install the frame.
![]() |
Using a T30 "TORX" socket, install the screw.
![]() |
w/ Entry and Start System:
Connect the clamp and connector.
| 8. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH |
w/ Entry and Start System:
Connect the connector.
![]() |
Install the handle by pushing and sliding it in the direction indicated by the arrows in the illustration.
| 9. INSTALL FRONT DOOR LOCK ASSEMBLY LH |
Apply MP grease to the sliding and rotating areas of the front door lock.
![]() |
Install the 2 cables as shown in the illustration.
![]() |
Attach the 3 claws to close the cover.
![]() |
Install a new door lock wire harness packing.
![]() |
Connect the control rod to the door lock, and then set it to the door panel.
Apply adhesive to the threads of the 3 screws.
![]() |
Using a T30 "TORX" socket, install the door lock with the 3 screws.
Connect the connector.
| 10. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side) |
Install the door lock cylinder to the cover.
![]() |
Using a T30 "TORX" socket, install the cover (with cylinder) with the screw.
Install the hole plug.
| 11. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Front Passenger Side) |
![]() |
Using a T30 "TORX" socket, install the cover with the screw.
Install the hole plug.
| 12. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Install the frame with the bolt.
| 13. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Using a T25 "TORX" driver, install the motor with the 3 screws.
| 14. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
![]() |
Apply MP grease to the sliding and rotating areas of the window regulator.
![]() |
Install the regulator with the 6 bolts.
Connect the connector.
| 15. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH |
![]() |
Install the door glass into the door panel along the glass run as indicated by the arrows in the illustration.
![]() |
Install the door glass to the window regulator with the 2 bolts.
| 16. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH |
![]() |
Attach the claws to install the belt moulding.
| 17. INSTALL FRONT DOOR SERVICE HOLE COVER LH |
![]() |
Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.
Connect each connector.
| 18. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH |
![]() |
Connect the 2 cables to the inside handle.
| 19. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY |
![]() |
Install the speaker with the 2 screws.
Connect the connector.
| 20. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Using an air riveter or hand riveter, install the speaker with 3 new rivets.
![]() |
![]() |
![]() |
Connect the connector.
| 21. INSTALL OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH |
![]() |
Pass the connector labeled A and wire harness of the mirror through the wire harness hole.
Temporarily install the mirror by inserting the bosses on the mirror into the holes on the vehicle and temporarily installing the 3 screws.
Tighten the 3 screws in the sequence shown in the illustration to install the mirror.
Connect the connector labeled A.
| 22. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH |
Attach the 4 claws to install the speaker door grille.
Attach the 7 claws to install the weatherstrip inner.
![]() |
Attach the 2 claws to install the inside handle.
![]() |
Attach the 10 clips to install the trim board.
Install the 3 screws.
![]() |
Attach the 3 claws to install the door inside handle bezel plug.
![]() |
Attach the 12 claws to install the door assist grip.
| 23. INSTALL FRONT ARMREST BASE PANEL UPPER LH |
![]() |
for Driver Side:
Install the power window regulator master switch to the panel with the 3 screws.
![]() |
for Passenger Side:
Attach the 2 claws and install the power window regulator switch to the panel.
Connect the switch connectors.
![]() |
Attach the clip and 5 claws to install the panel (with the switch).
| 24. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH |
![]() |
Attach the clip and 3 claws to install the garnish.
| 25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |