ENTRY AND START SYSTEM > Back Door Entry Unlock Function does not Operate |

| 1.CHECK FOR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
|
| ||||
| OK | |
| 2.CHECK MANUAL DOOR UNLOCK OPERATION |
Check that all the doors unlock when the door control switch (for manual operation) is turned to UNLOCK.
|
| ||||
| OK | |
| 3.CHECK WIRELESS DOOR LOCK CONTROL OPERATION |
Check that the wireless door lock and unlock functions operate normally (Click here).
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH) |
Check the Data List for proper functioning of the back door courtesy light switch.
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| Back Door Courtesy SW | Back door courtesy light switch signal / ON or OFF | ON: Back door is open OFF: Back door is closed | - |
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR SELECT) |
Select the Active Test, use the intelligent tester to generate a control command, and then check that the door electrical key oscillator operates.
| Item | Test Details | Diagnostic Note |
| Back Door Select | Door electrical key oscillator (back door) ON / OFF | - |
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (BACK DOOR UNLOCK SWITCH) |
With "Back Door Select" ON, check the Data List to confirm the operation of the touch sensor.
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| B-Door Touch Sensor | Back door touch sensor / ON or OFF | ON: Sensor touch is touched OFF: Sensor touch is not touched | - |
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (OPERATION) |
Temporarily replace the instrument panel junction block (main body ECU) with a new or normally functioning one.
Check that the entry back door unlock function operates normally.
|
| ||||
| OK | ||
| ||
| 8.CHECK DOOR ELECTRICAL KEY OSCILLATOR (for Back Door) |
![]() |
Measure the resistance of the oscillator.
| Tester Connection | Condition | Specified Condition |
| 4 (SEL) - Body ground | During Active Test | Below 1 V |
| 6 (SENS) - Body ground | Touch sensor is touched during Active Test | Below 1 V |
| Touch sensor is not touched during Active Test | 10 to 14 V |
|
| ||||
| NG | |
| 9.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - ELECTRICAL KEY ANTENNA) |
![]() |
Disconnect the S8 oscillator connector.
Disconnect the S9 antenna connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| S8-2 (SGT) - S9-6 (SGT) | Below 1 Ω |
| S8-3 (ANT1) - S9-5 (ANT1) | |
| S8-8 (ANT2) - S9-2 (ANT2) | |
| S8-9 (TRG-) - S9-1 (TRG-) | |
| S8-2 (SGT) or S9-6 (SGT) - Body ground | 10 kΩ or higher |
| S8-3 (ANT1) or S9-5 (ANT1) - Body ground | |
| S8-8 (ANT2) or S9-2 (ANT2) - Body ground | |
| S8-9 (TRG-) or S9-1 (TRG-) - Body ground |
|
| ||||
| OK | |
| 10.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
![]() |
Disconnect the E63 ECU connector.
Disconnect the S8 oscillator connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| E63-37 (SEL9) - S8-4 (SEL) | Below 1 Ω |
| E63-26 (SEN9) - S8-6 (SENS) | |
| E63-31 (CLG9) - S8-10 (CLG) | |
| E63-32 (CG9B) - S8-5 (CLGB) | |
| E63-37 (SEL9) or S8-4 (SEL) - Body ground | 10 kΩ or higher |
| E63-26 (SEN9) or S8-6 (SENS) - Body ground | |
| E63-31 (CLG9) or S8-10 (CLG) - Body ground | |
| E63-32 (CG9B) or S8-5 (CLGB) - Body ground |
|
| ||||
| OK | ||
| ||