Home › BODY ELECTRICAL › DOOR LOCK › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > Back Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

Neither the entry nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (back door), 2) the entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.

WIRING DIAGRAM


B133518E03


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. By following the tester screen display, check whether any DTCs are output.

    OK:
    No DTC output.



NG
Go to DIAGNOSTIC TROUBLE CODE CHART
OK


2.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION
  1. Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

    OK:
    All doors can be locked and unlocked with door control switch.



NG
Go to POWER DOOR LOCK CONTROL SYSTEM
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

    Certification ECU: 
    Item
    Test Details
    Diagnostic Note
    Outside Trunk/Backdoor Transmitter
    Door electrical key oscillator (back door) ON / OFF
    -

    OK:
    When key is brought close to door oscillator that is ON, indicator light on key illuminates.



OK
REPLACE ECU AGGREGATION BOX (CERTIFICATION ECU)
NG


4.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)
B108060E33
  1. Disconnect the E63 ECU connector.

  1. Disconnect the S8 oscillator connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E63-31 (CLG9) - S8-5 (CLGB)
    Below 1 Ω
    E63-32 (CG9B) - S8-10 (CLG)
    E63-31 (CLG9) or S8-5 (CLGB) - Body ground
    10 kΩ or higher
    E63-32 (CG9B) or S8-10 (CLG) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)
B108040E36
  1. Disconnect the S8 oscillator connector.

  1. Disconnect the S9 antenna connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S8-2 (SGT) - S9-6 (SGT)
    Below 1 Ω
    S8-3 (ANT1) - S9-5 (ANT1)
    S8-8 (ANT2) - S9-2 (ANT2)
    S8-9 (TRG-) - S9-1 (TRG-)
    S8-2 (SGT) or S9-6 (SGT) - Body ground
    10 kΩ or higher
    S8-3 (ANT1) or S9-5 (ANT1) - Body ground
    S8-8 (ANT2) or S9-2 (ANT2) - Body ground
    S8-9 (TRG-) or S9-1 (TRG-) - Body ground



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
B127160E06
  1. Disconnect the S8 oscillator connector.

  1. Measure the resistance and voltage of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    S9-7 (GND) - Body ground
    Below 1 Ω

    Standard voltage:
    Tester Connection
    Specified Condition
    S9-1 (+B) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
B127161E06
  1. Disconnect the S9 antenna connector.

  1. Disconnect the E62 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    S9-3 (TRG+) - E63-7 (TSW9)
    Below 1 Ω
    S9-3 (TRG+) or E63-7 (TSW9) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.CHECK BACK DOOR OUTSIDE HANDLE (OPERATION)
  1. Temporarily replace the back door outside handle with a new or normally functioning one.

  1. Check that the entry lock and unlock functions operate normally (Click here).

    OK:
    Entry lock and unlock functions operate normally.



NG
END (ELECTRICAL KEY ANTENNA IS DEFECTIVE)
OK


9.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Temporarily replace the door electrical key oscillator (back door) with a new or normally

  1. Check that the entry lock and unlock functions operate normally.

    OK:
    Entry lock and unlock functions operate normally.



NG
REPLACE ECU AGGREGATION BOX (CERTIFICATION ECU)
OK

END (DOOR KEY OSCILLATOR IS DEFECTIVE)