FRONT DRIVE SHAFT ASSEMBLY (for 2WD) > DISASSEMBLY |
| 1. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, remove the clamp as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, remove the clamp as shown in the illustration.
| 2. REMOVE FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH |
| 3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH |
![]() |
for One Touch Type Clamp:
Using a screwdriver, remove the clamp as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, remove the clamp as shown in the illustration.
| 4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH |
| 5. REMOVE FRONT AXLE INBOARD JOINT BOOT |
Remove the boot from the inboard joint.
| 6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH |
![]() |
Remove any old grease from the inboard joint.
Put matchmarks on the inboard joint and outboard joint shaft.
Remove the inboard joint from the outboard joint shaft.
![]() |
Using a snap ring expander, remove the shaft snap ring.
![]() |
Put matchmarks on the outboard joint shaft and tripod.
Using a brass bar and hammer, tap off the tripod from the outboard joint shaft.
Remove the inboard joint boot.
| 7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH |
| 8. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (for LH Side) |
![]() |
for One Touch Type Clamp:
Using a screwdriver, remove the clamp as shown in the illustration.
for Claw Engagement Type Clamp:
Using needle-nose pliers, remove the clamp as shown in the illustration.
| 9. REMOVE FRONT DRIVE SHAFT DAMPER LH |
Remove the front drive shaft damper from the outboard joint shaft.
| 10. REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH |
![]() |
Using a screwdriver, remove the outboard joint boot clamp as shown in the illustration.
| 11. REMOVE FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH |
| 12. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH |
![]() |
Using a screwdriver, remove the outboard joint boot clamp as shown in the illustration.
| 13. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH |
| 14. REMOVE FRONT AXLE OUTBOARD JOINT BOOT |
Remove the outboard joint boot from the outboard joint shaft.
Remove any old grease from the outboard joint.
| 15. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH |
![]() |
Using a screwdriver, remove the hole snap ring.
| 16. REMOVE FRONT DRIVE SHAFT DUST COVER LH |
![]() |
Using SST and a press, press out the inboard joint from the shaft dust cover to remove the shaft dust cover.
| 17. REMOVE FRONT DRIVE SHAFT DUST COVER RH |
| 18. REMOVE DRIVE SHAFT BEARING CASE |
![]() |
Using a screwdriver, remove the bearing case snap ring from the snap ring groove.
![]() |
Using a press, press out the inboard joint from the drive shaft bearing case to remove the drive shaft bearing.
| 19. REMOVE FRONT DRIVE SHAFT DUST COVER |
![]() |
Using SST and a press, press out the inboard joint from the shaft dust cover to remove the shaft dust cover.
| 20. REMOVE FRONT DRIVE SHAFT BEARING |
![]() |
Using a snap ring expander, remove the snap ring.
![]() |
Using SST and a press, press out the inboard joint from the drive shaft bearing to remove the drive shaft bearing.
Remove the bearing case snap ring from the inboard joint.