Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2WD)

FRONT DRIVE SHAFT ASSEMBLY (for 2WD) > REASSEMBLY

for Preparation Click here



1. INSTALL DRIVE SHAFT BEARING CASE SUB-ASSEMBLY


C127674E01
  1. Using SST and a press, press the drive shaft bearing case onto the inboard joint RH.

    SST
    09527-10011  
    09710-04081  

    NOTICE:
    Make sure the bearing is completely installed.



    C127675
  1. Using a snap ring expander, install a new snap ring.



2. INSTALL FRONT DRIVE SHAFT DUST COVER


C127676E02
  1. Using SST and a press, press in a new drive shaft dust cover.

    SST
    09726-40010  
    09527-10011  

    Standard dust cover depth:
    1 mm (0.0394 in.)

    NOTICE:
    Be careful not to damage the dust cover.



3. INSTALL FRONT DRIVE SHAFT DUST COVER RH


C127678E01
  1. Using SST and a press, press a new drive shaft dust cover onto the inboard joint until the distance from the tip of the inboard joint to the drive shaft dust cover reaches the specification as shown in the illustration.

    SST
    09527-10011  

    Standard distance:
    110.0 to 111.0 mm (4.330 to 4.370 in.)

    NOTICE:
    Be careful not to damage the dust cover.



4. INSTALL FRONT DRIVE SHAFT DUST COVER LH


C127677E01
  1. Using SST and a press, press in a new drive shaft dust cover onto the inboard joint.

    SST
    09527-10011  

    NOTICE:
    1. The dust cover should be installed completely.
    2. Be careful not to damage the dust cover.



5. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new hole snap ring.



6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT


C127681E01

HINT:
Before installing the boots, wrap the splines of the shaft with vinyl tape to prevent the boots from being damaged.

  1. Temporarily install a new outboard joint boot No. 2 clamp to the outboard joint shaft.

  1. Install a new outboard joint boot so that it is between the outboard joint boot No. 2 clamp and outboard joint shaft.

  1. Temporarily install a new outboard joint boot clamp to the outboard joint boot.

  1. Pack the outboard joint shaft and boot with grease from the boot kit.

    Standard grease capacity:
    205 to 215 g (7.2 to 7.6 oz.)



7. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP LH


C127683

CAUTION:
Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

    NOTICE:
    1. When temporarily bending the lever, make sure not to deform the band and lever.
    2. Set the clamp correctly in the guide groove and align it with the interior of the vehicle as much as possible.



    C127684
  1. With the joint on a flat surface, use your body weight to press down on the joint with one hand. Then, roll the joint forward as shown in the illustration, and press the lever in until a "click" sound is heard.

    NOTICE:
    1. Do not damage the deflector.
    2. Make sure the joint is in full contact with the surface at all times.



    C127685
  1. Using a plastic-faced hammer, fix the buckle into place by tapping it. At the same time, use the plastic-faced hammer to adjust the lift of the lever so that the gaps between the buckle flange and lever end flange become even.

    NOTICE:
    Do not damage the boot.



8. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.



9. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH


C129510

CAUTION:
Wear protective gloves while performing the operation and be careful to avoid cutting your hands or other body parts.

  1. Install a new boot clamp to the outboard joint boot and temporarily bend the lever.

    NOTICE:
    When temporarily bending the lever, make sure not to deform the band and lever.



    C129511
  1. Using water pump pliers, temporarily lock the boot clamp by bending the lever down until a "click" sound is heard.



    C129512
  1. Using a plastic-faced hammer, bend the tabs of the buckle to fix the lever in place. At the same time, use the plastic-faced hammer to adjust the position of the lever so that the end of the lever is aligned with the edge of the buckle.

    NOTICE:
    Do not strike the shaft forcefully with the plastic-faced hammer.



10. TIGHTEN FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL FRONT DRIVE SHAFT DAMPER LH (for LH Side)


C127690E01
  1. Secure the shaft in a vise between aluminum plates.

  1. Temporarily install a new drive shaft damper clamp to the shaft, and then install the drive shaft damper so that it is between the damper clamp and shaft.

    HINT:
    Make sure the damper clamp is on the outboard joint side.

  1. Adjust the position of the drive shaft damper so that the distance shown in the illustration is within the specified range.

    Standard distance:
    158 to 162 mm (6.220 to 6.378 in.)



12. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP LH (for LH Side)


C127651E28
  1. Secure the shaft in a vise between aluminum plates.

  1. Tighten the drive shaft damper clamp.

    NOTICE:
    Make sure the clamp is installed in the correct position.


    1. for One Touch Type Clamp:
      Using a screwdriver, tighten the drive shaft damper clamp as shown in the illustration.

    2. for Claw Engagement Type Clamp:
      Using needle-nose pliers, tighten the drive shaft damper clamp as shown in the illustration.



13. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY LH

HINT:
Before installing the boots, wrap the splines of the shaft with vinyl tape to prevent the boots from being damaged.

  1. Wrap the splines of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.

  1. Install new parts to the outboard joint shaft in the following order.

    1. Inboard joint boot clamp

    2. No. 2 inboard joint boot clamp

    3. Inboard joint clamp



    C127694E02
  1. Place the tripod so that the beveled side of the tripod axial splines faces toward the outboard joint.

  1. Align the matchmarks placed before removal.

  1. Using a brass bar and hammer, tap the tripod onto the shaft.

    NOTICE:
    1. Do not tap the rollers.
    2. Be sure to install the tripod in the correct direction.

  1. Pack the inboard joint shaft and boot with grease from the boot kit.

    Standard grease capacity:
    175 to 185 g (6.2 to 6.5 oz.)



    C127695
  1. Using a snap ring expander, install a new shaft snap ring.

  1. Align the matchmarks and install the inboard joint to the outboard joint shaft.



14. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



15. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the boot to the inboard joint.



16. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP LH


C127696E03
  1. for One Touch Type Clamp:
    Using a screwdriver, tighten the clamp as shown in the illustration.

    NOTICE:
    Be careful not to damage the boot.

  1. for Claw Engagement Type Clamp:
    Using needle-nose pliers, tighten the clamp as shown in the illustration.

    NOTICE:
    Be careful not to damage the boot.



17. TIGHTEN FRONT AXLE INBOARD JOINT BOOT CLAMP RH

HINT:
Use the same procedures described for the LH side.



18. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP LH


C127697E03
  1. for One Touch Type Clamp:
    Using a screwdriver, tighten the clamp as shown in the illustration.

    NOTICE:
    Be careful not to damage the boot.

  1. for Claw Engagement Type Clamp:
    Using needle-nose pliers, tighten the clamp as shown in the illustration.

    NOTICE:
    Be careful not to damage the boot.



19. TIGHTEN FRONT AXLE INBOARD JOINT BOOT NO. 2 CLAMP RH

HINT:
Use the same procedures described for the LH side.



20. INSPECT FRONT DRIVE SHAFT


C206075
  1. Secure the shaft in a vise between aluminum plates.

  1. Check that there is no severe play in the radial direction of the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no severe play in the radial direction of the inboard joint.

  1. Check the boots for damage.



    C127699E01
  1. Measure length (A) of the drive shaft.

    NOTICE:
    Keep the drive shaft assembly level during inspection.

    Standard (Reference):
    Item
    Drive shaft LH (Dimension)
    Drive shaft RH (Dimension)
    for EA64
    553.6 mm (1.82 ft.)
    932.4 mm (3.06 ft.)