Home › DRIVE LINE › DRIVE SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 4WD)

FRONT DRIVE SHAFT ASSEMBLY (for 4WD) > REMOVAL

for Preparation Click here




1. REMOVE FRONT WHEEL


2. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the refill plug and gasket from the automatic transaxle.



    C205876
  1. Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the automatic transaxle.



    C162883E04
  1. Using a 6 mm socket hexagon wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle and drain the automatic transaxle fluid.

  1. Using a 6 mm socket hexagon wrench, install the No. 1 transmission oil filler tube to the automatic transaxle.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }

    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Hexagon Socket Wrench
    *3
    Overflow Plug Hole

  1. Using a 6 mm socket hexagon wrench, install a new gasket and the overflow plug to the automatic transaxle.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Temporarily install the gasket and the refill plug to the automatic transaxle.



3. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



4. REMOVE FRONT AXLE HUB NUT


    C129483E01
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub nut.



5. REMOVE FRONT SPEED SENSOR LH


    C127964E05
  1. Disconnect the sensor connector.



    C193404E01
  1. Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).



  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).


    C127962E01



    C127961E01
  1. Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.



6. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



7. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY LH


C127058
  1. Remove the 2 bolts and cylinder.



8. DISCONNECT FRONT DISC BRAKE CYLINDER ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



9. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


    C127528
  1. Remove the 2 nuts and stabilizer link.



10. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



11. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH


    C127531
  1. Remove the bolt and 2 nuts.

  1. Disconnect the lower arm from the ball joint.



12. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



13. DISCONNECT STEERING KNUCKLE WITH AXLE HUB LH


C129488E01
  1. Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. Using a plastic-faced hammer, disconnect the steering knuckle with axle hub.

    NOTICE:
    1. Be careful not to damage the boot and speed sensor rotor.
    2. Do not excessively push out the drive shaft from the axle assembly.



14. DISCONNECT STEERING KNUCKLE WITH AXLE HUB RH

HINT:
Use the same procedures described for the LH side.



15. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.



    C132680E01
  1. Using SST, disconnect the tie rod end from the steering knuckle.

    NOTICE:
    Do not damage the tie rod end dust cover.

    SST
    09628-62011  



16. DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



17. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C127631E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft.



18. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C127640
  1. Squeeze the ends of the snap ring, and remove the snap ring from the bearing bracket.

  1. Remove the bearing bracket bolt and front drive shaft from the bearing bracket.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the boot.
    3. Do not allow the drive shaft to fall off.

    HINT:
    If the connection is stiff, use a brass bar and hammer to lightly tap the edge of the inboard joint RH and remove it.