Home › DRIVE LINE › DRIVE SHAFT › REAR DRIVE SHAFT ASSEMBLY

REAR DRIVE SHAFT ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. INSTALL REAR DRIVE SHAFT ASSEMBLY LH
  1. Align the splines of the rear drive shaft outboard joints and, install the left and right rear drive shafts to the axle hub.



2. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
  1. Apply hypoid gear oil to the splines of the left and right rear drive shaft inboard joints.



    C129504
  1. Align the splines of the rear drive shaft inboard joints and, using a brass bar and hammer, tap in the left and right rear drive shafts.

    NOTICE:
    1. Face the cutout section of the snap ring downward.
    2. Do not damage the oil seal during the insertion.
    3. Do not strike the tip of the outboard joint with the hammer.

    HINT:
    Determine whether or not the rear drive shaft is completely tapped in by checking for changes in sound or the reaction force of the brass bar.



    C129479E01
  1. Slowly raise the transmission jack, fix the nuts in place and install the 3 bolts.

    Torque:
    86 N*m{ 877 kgf*cm , 63 ft.*lbf } for bolt A
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf } for bolt B

    NOTICE:
    Tighten the bolts, not the nuts.



3. INSTALL REAR SPEED SENSOR LH
  1. Install the speed sensor .



4. INSTALL REAR AXLE SHAFT NUT
  1. Clean the threaded parts on the drive shaft and a new axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Install a new hub nut.

    Torque:
    216 N*m{ 2203 kgf*cm , 159 ft.*lbf }



    C129485
  1. Using a chisel and hammer, stake the hub nut.



5. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    C127526E01
  1. Align the matchmarks of the transfer and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.



    C127525E01
  1. Align the matchmarks of the differential carrier and propeller shaft.

  1. Temporarily install the propeller shaft with center bearing with the 4 nuts and 4 washers.



    C127524
  1. Temporarily install the center support bearing and center support bearing washer with the 2 bolts.



6. TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Tighten the 4 nuts of the propeller shaft and transfer to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Tighten the 4 nuts of the propeller shaft and differential carrier to the torque specification.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Check that the center line of the center support bearing housing is perpendicular to the axis of the propeller shaft.

  1. Tighten the 2 bolts of the center support bearing to the torque specification.

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }



7. INSPECT JOINT ANGLE

NOTICE:
Perform the measurement with a 4 post lift or pit so that the vehicle is supported by all 4 wheels as if it were on the ground.

  1. Before the angle measurement, stabilize each part by performing procedures like those described below.

    1. Rotate the propeller shaft several times by hand.

    2. Set the jack to the differential, and raise and lower the differential.



  1. Using SST and a straightedge, measure the angle of the transfer flange (angle D) and the angle of the intermediate shaft (angle A).

    SST
    09370-50010  

    NOTICE:
    Make sure the straightedge and SST are at a right angle.



    C190639E01


    1. Subtract the measured angle of the intermediate shaft (angle A) from the measured angle of the transfer flange (angle D) to obtain the No. 1 joint angle.

      No. 1 Joint Angle:
      Measurement Position
      Engine
      Transmission
      No. 1 Joint Angle
      D - A
      2AD-FTV
      2AD-FHV
      M/T
      2°27' +/-60'
      2AD-FHV
      A/T
      2°31' +/-60'



  1. Using SST, measure the angle of the intermediate shaft (angle A) and the angle of the propeller shaft (angle B).

    SST
    09370-50010  


    C190640E01


    1. Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the intermediate shaft (angle A) to obtain the No. 2 joint angle.

      No. 2 Joint Angle:
      Measurement Position
      Engine
      Transmission
      No. 2 Joint Angle
      A - B
      2AD-FTV
      2AD-FHV
      M/T
      1°29' +/-1°30'
      2AD-FHV
      A/T
      1°59' +/-1°30'



  1. Using SST, measure the angle of the propeller shaft (angle B) and the angle of the rear differential (angle C).

    SST
    09370-50010  


    C190641E01


    1. Subtract the measured angle of the propeller shaft (angle B) from the measured angle of the rear differential (angle C) to obtain the No. 3 joint angle.

      No. 3 Joint Angle:
      Measurement Position
      Engine
      Transmission
      No. 3 Joint Angle
      B - C
      2AD-FTV
      2AD-FHV
      M/T
      2°10' +/-60'
      2AD-FHV
      A/T
      2°06' +/-60'



8. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front pipe for 2AD-FTV .

  1. Install the front pipe for 2AD-FHV .



9. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe for 2AD-FTV .

  1. Install the tailpipe for 2AD-FHV .



10. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



11. ADD DIFFERENTIAL OIL
  1. Add differential oil .



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


13. INSPECT FOR DIFFERENTIAL OIL LEAK


14. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


15. INSPECT REAR WHEEL ALIGNMENT
  1. Inspect the rear wheel alignment (Click here).