Home › SUSPENSION & AXLE › SUSPENSION › FRONT SUSPENSION LOWER NO. 1 ARM

FRONT SUSPENSION LOWER NO. 1 ARM > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL


2. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the hood (Click here).



3. SUSPEND ENGINE ASSEMBLY (for 2AD-FTV)


    A197280
  1. Remove the bolt and disconnect the cable bracket.



    A208840
  1. Set an engine lifter underneath the engine.

    HINT:
    Place the engine on wooden blocks or equivalent so that the engine is level.



    A212797
  1. Remove the 2 bolts and 2 nuts, and disconnect the engine mounting insulator RH.



    A202311
  1. Remove the bolt and nut and disconnect the engine mounting insulator LH.



    A205806
  1. Remove the 6 bolts and front suspension member rear brace RH and LH.

  1. Remove the 2 bolts from the front suspension crossmember.

  1. Carefully remove the engine with transaxle from the vehicle.



    A202315E01
  1. Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No. 
    No. 1 engine hanger
    12281-26040
    No. 2 engine hanger
    12282-26010
    Bolt
    90105-81025 or 90105-W0042
    1. Insert the claw of the No. 1 engine hanger into the hole of the cylinder head.
    2. Fit the fork part of the No. 2 engine hanger onto the rib of the cylinder head.

  1. Attach an engine sling device and hang the engine with a chain block.



4. SUSPEND ENGINE ASSEMBLY (for 2AD-FHV)


    A197280
  1. Remove the bolt and disconnect the cable bracket.



    A208840
  1. Set an engine lifter underneath the engine.

    HINT:
    Place the engine on wooden blocks or equivalent so that the engine is level.



    A212797
  1. Remove the 2 bolts and 2 nuts, and disconnect the engine mounting insulator RH.



    A202311
  1. Remove the bolt and nut, and disconnect the engine mounting insulator LH.



    A205806
  1. Remove the 6 bolts and front suspension member rear brace RH and LH.

  1. Remove the 2 bolts and disconnect the suspension crossmember from the vehicle body.

  1. Carefully remove the engine with transaxle from the vehicle.



    A202315E01
  1. Install 2 engine hangers with 2 bolts as shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No. 
    No. 1 engine hanger
    12281-26040
    No. 2 engine hanger
    12282-26010
    Bolt
    90105-81025 or 90105-W0042
    1. Insert the claw of the No. 1 engine hanger into the hole of the cylinder head.
    2. Fit the fork part of the No. 2 engine hanger onto the rib of the cylinder head.

  1. Attach an engine sling device and hang the engine with a chain block.



5. REMOVE FRONT STABILIZER LINK ASSEMBLY LH


    C127528
  1. Remove the 2 nuts and stabilizer link.



6. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH


C127531
  1. Remove the 2 nuts and bolt, and disconnect the lower arm from the ball joint.



7. DISCONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



8. DISCONNECT FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY


A124842
  1. Remove the 2 nuts, 2 bolts and rear engine mounting insulator.



    C131836
  1. Remove the bolt from the suspension member.



    C131835E01
  1. Support the crossmember with the jack.

  1. Remove the bolts labeled A.

    1. Remove the 4 bolts from the member reinforcement.

  1. Remove the bolts labeled B.

    1. Remove the 6 bolts from the member brace.

  1. Slowly lower the jack, and disconnect the crossmember from the vehicle.



9. REMOVE FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH


C131838
  1. Remove the bolt and nut from the suspension member (front side).



    C131833
  1. Remove the bolt and nut from the suspension member (rear side). Then remove the lower arm.



10. REMOVE FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.