REAR NO. 1 SEAT ASSEMBLY (for RH Side) > REMOVAL |
| 1. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
| 2. REMOVE TONNEAU COVER ASSEMBLY |
| 3. REMOVE REAR FLOOR NO. 1 BOARD |
| 4. REMOVE DECK BOARD ASSEMBLY |
| 5. REMOVE REAR FLOOR NO. 3 BOARD |
| 6. REMOVE REAR FLOOR NO. 2 BOARD |
| 7. REMOVE JACK CARRIER ASSEMBLY (for Short Body) |
![]() |
Using a clip remover, remove the 7 clips and remove the jack carrier.
| 8. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Short Body) |
![]() |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 9. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (for Long Body) |
![]() |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 10. REMOVE BACK DOOR WEATHERSTRIP |
| 11. REMOVE REAR FLOOR FINISH PLATE (for Short Body) |
![]() |
Using a clip remover, detach the 6 clips and remove the finish plate.
| 12. REMOVE REAR FLOOR FINISH PLATE (for Long Body) |
![]() |
Using a clip remover, detach the 6 clips.
Detach the 2 claws and remove the finish plate.
| 13. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH |
![]() |
Using a screwdriver, detach the 6 claws and remove the bezel.
| 14. REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY (for Long Body) |
![]() |
Remove the bolt and tether anchor bracket.
| 15. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body) |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 16. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body) |
![]() |
Remove the bolt, 2 washers, collar and bracket.
| 17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Short Body) |
![]() |
Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 5 clips and remove the trim board.
Remove the belt hanger.
| 18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Long Body) |
![]() |
Disconnect the rear No.1 seat outer belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the 2 screws and 2 bolts.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 4 clips and remove the trim board.
Remove the belt hanger.
| 19. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH |
![]() |
Remove the 2 bolts and lever.
Disconnect the rear No. 1 seat lock cable from the lever.
| 20. REMOVE REAR NO. 3 SEAT LEG SIDE COVER |
![]() |
Using a screwdriver, detach the 4 claws and remove the side cover.
| 21. REMOVE REAR NO. 2 SEAT LEG SIDE COVER |
![]() |
Using a screwdriver, detach the 3 claws and clip, remove the side cover.
| 22. REMOVE REAR SEAT LEG COVER |
![]() |
Using a screwdriver, detach the 8 claws and remove the 2 leg covers.
| 23. REMOVE REAR NO. 1 SEAT LOCK CABLE ASSEMBLY |
Disconnect the lock cable from the seat.
Raise the adjuster's lock piece to release the lock.

![]() |
Slide the seat forward and tilt the seatback forward.
![]() |
Remove the seat's cap from the connector case.
![]() |
Pull the seat's cap toward the outside of the vehicle. Then remove the cable from the connector case's slit.
![]() |
Remove the body's cap from the connector case.
Detach the clamps and remove the lock cable.

| 24. REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
Lift up the seat track adjusting handle and move the seat to the rearmost position.
![]() |
Remove the 2 bolts on the front side of the seat.
Lift up the seat track adjusting handle and move the seat to the foremost position.
![]() |
Remove the 3 bolts on the rear side of the seat.
Fully tilt the seatback forward. Then remove the seat.