Home › BODY › SEAT › REAR NO. 1 SEAT ASSEMBLY (for LH Side)

REAR NO. 1 SEAT ASSEMBLY (for LH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL REAR SEAT COVER LH


    B135847
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.



2. INSTALL REAR SEATBACK COVER LH


    B135846
  1. Attach the 2 claws to install the cover.

  1. Install the 2 screws.



3. INSTALL REAR NO. 1 SEATBACK COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B135848E01
  1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.

  1. Install the seatback cover (with pad) to the seatback frame.



    B060977E01
  1. Attach the 4 claws to install the 2 headrest supports.



    B132487E01
  1. Lift up the seatback cover and install the 13 hog rings.



4. INSTALL REAR SEATBACK PROTECTOR


    B140225
  1. Install the protector with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the clip.



    B132488E01
  1. Attach the 2 clips and close the fastening tape.



5. INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY CENTER LH


B130992
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



6. INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH


    B132493
  1. Install the seatback with the 5 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B140223
  1. Attach the 2 clamps and connect the cable to the reclining adjuster.



7. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH


    B135842
  1. Attach the 2 claws to install the lever base.

  1. Install the screw.



8. INSTALL REAR SEAT RECLINING RELEASE LEVER


    B140199E01
  1. Attach the claw to install the release lever.



    B140195
  1. Install the cover with the 2 screws.



9. INSTALL REAR SEAT CUSHION MOULDING LH


    B131539
  1. Attach the 2 claws to install the moulding.

  1. Install the screw.



10. INSTALL REAR SEAT CUSHION REAR MOULDING LH


    B132494
  1. Attach the claw to install the moulding.

  1. Install the screw.



11. INSTALL REAR SEAT REAR BRACKET COVER LH


    B135844
  1. Open the lower part of the seatback cover. Then attach the 4 clips to install the bracket cover.

  1. Install the 2 screws.



12. INSTALL REAR NO. 1 SEAT CUSHION COVER

NOTICE:
  1. Be careful not to damage the cover.
  2. When installing the hog rings, avoid wrinkling the cover.



    B140005E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 3 new hog rings.



    B132489E01
  1. Using hog ring pliers, install the seat cushion cover (with pad) to the seat cushion frame with 29 new hog rings.



    B140222
  1. Attach the 2 hooks.



13. INSTALL REAR NO. 1 SEAT CUSHION ASSEMBLY LH


    B132502
  1. Install the cushion with the 2 bushes and 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    B140219E01
  1. Install the 2 bolts.



14. INSTALL REAR SEAT INNER BELT ASSEMBLY RH


B138224
  1. Install the belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



15. INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH


    B131541
  1. Attach the 5 claws to install the hinge cover.



16. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER


    B132503
  1. Attach the 6 claws to install the hinge cover.



17. INSTALL REAR NO. 1 SEAT ARMREST ASSEMBLY LH


    B140215
  1. Install the armrest with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



18. INSTALL REAR SEAT CENTER ARMREST COVER


    B140218
  1. Push the armrest cover in the direction indicated by the arrow in the illustration to attach the 2 claws.



    B140216
  1. Attach the 2 clips to install the armrest cover.



19. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    B132505
  1. Install the armrest with the 2 nuts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



20. INSTALL CENTER ARMREST HINGE COVER LH


    B140214
  1. Attach the 4 claws to install the hinge cover.



21. INSTALL CENTER ARMREST HINGE COVER RH
  1. Pass the seat lock release strap through the hole in the hinge cover.

  1. Attach the claw to install the hinge cover.



    B132496
  1. Install the 2 screws and 2 rear seatback lock hooks.



22. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY


23. INSTALL REAR SEAT HEADREST ASSEMBLY