Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSPECTION

for Preparation Click here



1. INSPECT SHIFT LOCK CONTROL ECU


C197449E03
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage and Resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (ACC) - 1 (E)
    Ignition switch ON
    11 to 14 V
    6 (ACC) - 1 (E)
    Ignition switch ACC
    11 to 14 V
    6 (ACC) - 1 (E)
    Ignition switch off
    Below 1 V
    4 (STP) - 1 (E)
    Brake pedal depressed
    11 to 14 V
    4 (STP) - 1 (E)
    Brake pedal released
    Below 1 V
    5 (KLS+) - 1 (E)
    1. Ignition switch ACC and shift lever in P
    Below 1 V
    2. Ignition switch ACC and shift lever not in P (Within approx. 1 second)
    7.5 to 11 V
    3. Ignition switch ACC and shift lever not in P (After approx. 2 seconds)
    6 to 9.5 V
    8 (IG) - 1 (E)
    Ignition switch ON
    11 to 14 V
    8 (IG) - 1 (E)
    Ignition switch off
    Below 1 V
    1 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Component with harness connected
    (Shift Lock Control ECU)

    HINT:
    Do not disconnect the floor shift assembly connector.

    If the result is not as specified, replace the shift lock control ECU.



2. INSPECT TRANSMISSION CONTROL SWITCH


C203344E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (IG) - 7 (S)
    Shift lever in M, "+" or "-"
    Below 1 Ω
    2 (SFTU) - 5 (E)
    Shift lever held in "+" (Up-shift)
    Below 1 Ω
    1 (SFTD) - 5 (E)
    Shift lever held in "-" (Down-shift)
    Below 1 Ω
    3 (IG) - 7 (S)
    Shift lever not in M, "+" or "-"
    10 kΩ or higher
    2 (SFTU) - 5 (E)
    Shift lever in M
    10 kΩ or higher
    1 (SFTD) - 5 (E)
    Shift lever in M
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Transmission Control Switch)
    If the result is not as specified, replace the shift lock control unit.



3. INSPECT SHIFT LOCK SOLENOID
  1. Disconnect the shift lock solenoid connector.



    C197452E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (P) - 3 (E2)
    Shift lever in P
    10 kΩ or higher
    4 (P) - 3 (E2)
    Shift lever not in P
    Below 1 Ω
    2 (SLS-) - 1 (SLS+)
    Always
    112 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Shift Lock Solenoid)
    If the result is not as specified, replace the shift lock control unit.