Home › TRANSMISSION ยท EA64 MANUAL TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > REPLACEMENT

for Preparation Click here



1. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


C127631E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft.



2. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    C127640
  1. Squeeze the ends of the snap ring, and remove the snap ring from the bearing bracket.

  1. Remove the bearing bracket bolt and front drive shaft from the bearing bracket.

    NOTICE:
    1. Do not damage the oil seal.
    2. Do not damage the boot.
    3. Do not allow the drive shaft to fall off.

    HINT:
    If the connection is stiff, use a brass bar and hammer to lightly tap the edge of the inboard joint RH and remove it.



3. REMOVE TRANSAXLE CASE OIL SEAL LH


D025305E09
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



4. REMOVE TRANSAXLE CASE OIL SEAL RH


C094266E04
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  



5. INSTALL TRANSAXLE CASE OIL SEAL LH


D026133E10
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-10010  
    09950-70010   (09951-07200)

    Standard depth:
    -0.5mm to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the lip of the oil seal.



6. INSTALL TRANSAXLE CASE OIL SEAL RH


D025722E02
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-32010  
    09950-70010   (09951-07200)

    Standard depth:
    -0.5mm to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Do not damage the lip of the oil seal.



7. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


C127700
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and tap in the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.



8. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the splines of the inboard joint shaft with gear oil.

  1. Align the shaft splines and securely insert the drive shaft.

    NOTICE:
    Do not damage the oil seal.



    C127640
  1. Squeeze the ends of the snap ring and install it to the bearing bracket.

  1. Install a new bearing bracket bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



9. ADD MANUAL TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transmission filler plug and the gasket.



    D025304E21
  1. Check that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transmission oil.

    NOTICE:
    1. Too much or too little oil may cause trouble.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install a new gasket and the transmission filler plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



10. INSPECT MANUAL TRANSAXLE OIL
  1. Inspect the manual transfer oil .