AUTOMATIC TRANSAXLE UNIT > INSPECTION |
| 1. INSPECT TRANSMISSION OIL CLEANER MAGNET |
![]() |
Examine the particles in the oil pan.
Use the removed magnets to collect any steel chips. Look carefully at the chips and particles in the pan and on the magnet to anticipate what type of wear you will find in the transaxle.
Steel (magnetic): bearing, gear and plate wear
Brass (non-magnetic): bush wear
| 2. INSPECT INPUT SHAFT SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 3. INSPECT NO. 2 CLUTCH DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 4. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the bushings of the planetary sun gear.
| 5. INSPECT NO. 1 CLUTCH DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 6. INSPECT NO. 3 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flanges are worn or burnt.
| 7. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the clearance between the underdrive planetary gear and the pinion gear at 4 points.
| 8. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the bushing of the rear planetary sun gear sub-assembly.
| 9. INSPECT NO. 1 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 10. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the 3 2nd brake piston return springs including the spring seats.
| 11. INSPECT ONE-WAY CLUTCH ASSEMBLY |
![]() |
Temporarily install the one-way clutch assembly to the planetary ring gear.
Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
If the one-way clutch assembly does not operate as specified, replace it.
| 12. INSPECT PLANETARY GEAR ASSEMBLY |
![]() |
Using a feeler gauge, measure the clearance between the planetary gear case and each pinion gear at points A and B.
| Measuring Point | Standard Clearance |
| A | 0.23 to 0.59 mm (0.00906 to 0.0232 in.) |
| B | 0.16 to 0.66 mm (0.00630 to 0.0259 in.) |
| 13. INSPECT NO. 2 BRAKE DISC |
![]() |
Check if the contact surfaces of the discs, plates and flange are worn or burnt.
| 14. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using a vernier caliper, measure the free length of the 1st and reverse brake return spring together with the spring seat.
| 15. INSPECT PISTON STROKE OF NO. 2 BRAKE |
![]() |
Using a dial indicator, measure the piston stroke of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness |
| 40 | 4.0 mm (0.157 in.) |
| 41 | 4.1 mm (0.161 in.) |
| 42 | 4.2 mm (0.165 in.) |
| 43 | 4.3 mm (0.169 in.) |
| 44 | 4.4 mm (0.173 in.) |
| 16. INSPECT PISTON STROKE OF NO. 1 BRAKE |
![]() |
Using a dial indicator, measure the piston stroke of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness |
| 30 | 3.0 mm (0.118 in.) |
| 31 | 3.1 mm (0.122 in.) |
| 32 | 3.2 mm (0.126 in.) |
| 33 | 3.3 mm (0.130 in.) |
| 34 | 3.4 mm (0.134 in.) |
| 35 | 3.5 mm (0.138 in.) |
| 17. INSPECT CLEARANCE OF NO. 3 BRAKE |
![]() |
Using a vernier caliper and straightedge, measure the distance shown in the illustration (dimension A) while a load of 500 N (51 kgf, 112 lbf) is being applied to the flange.
Using a vernier caliper and straightedge, measure the distance from the contact surface of the front oil pump to the end of the No. 3 brake piston shown in the illustration (dimension B).
| *1 | Front Oil Pump Assembly |
| *2 | No. 3 Brake Piston |
| *3 | No. 3 Brake Flange for Adjustment |
Calculate the clearance value using the following formula:
Clearance = Dimension B - Dimension A
| Mark | Thickness |
| 38 | 3.80 mm (0.150 in.) |
| 39 | 3.90 mm (0.154 in.) |
| 40 | 4.00 mm (0.157 in.) |
| 41 | 4.10 mm (0.161 in.) |
| 42 | 4.20 mm (0.165 in.) |
| 43 | 4.30 mm (0.169 in.) |
| 18. INSPECT PISTON STROKE OF NO. 1 CLUTCH |
![]() |
Install the direct multiple disc clutch to the rear transaxle cover.
Using a dial indicator, measure the piston stroke of the No. 1 clutch while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness |
| 30 | 3.0 mm (0.118 in.) |
| 31 | 3.1 mm (0.122 in.) |
| 32 | 3.2 mm (0.126 in.) |
| 33 | 3.3 mm (0.130 in.) |
| 34 | 3.4 mm (0.134 in.) |
| 35 | 3.5 mm (0.138 in.) |
| 19. INSPECT PISTON STROKE OF NO. 2 CLUTCH |
![]() |
Install the direct multiple disc clutch assembly to the rear transaxle cover sub-assembly.
Using a dial indicator, measure the piston stroke of the No. 2 clutch while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
| Mark | Thickness |
| 30 | 3.0 mm (0.118 in.) |
| 31 | 3.1 mm (0.122 in.) |
| 32 | 3.2 mm (0.126 in.) |
| 33 | 3.3 mm (0.130 in.) |
| 34 | 3.4 mm (0.134 in.) |
| 35 | 3.5 mm (0.138 in.) |